Read and get familiar with all safety precautions and procedures before using the product. Strictly follow all safety precautions. Ensure that the product is properly assembled.

General safety precautions

■ The product can work only with Class 4 xTool F1 Ultra or Class 4 xTool F2 Ultra. Read and get familiar with all safety precautions and procedures about xTool F1 Ultra and xTool F2 Ultra before using the product.

■ Check the product for damage every time before you use it. Do not operate it in any way when any damage or defect is found.

■ Ensure that the workspace is clean and flat.

■ Do not leave the product unattended during operation. Pay attention to whether it is working properly.

■ Do not disassemble the product or change its structure in any way without authorization.

■ Keep the product away from moisture to prevent rust and corrosion.

■ The product works properly at the temperature of 0℃ to 35℃. Do not operate it at a temperature lower than 0℃.

■ Do not laser cut any materials or laser engrave thin, light-permeable materials (such as paper and cloth) on the conveyor. Laser beams falling on the belt will damage it.

Laser safety

Lasers are categorized into several different classes depending on the extent of the potential hazard associated with the laser, with Class 1 being the least dangerous and Class 4 the most dangerous. The United States Food and Drug Administration has indicated that Class 4 lasers may pose an "immediate skin hazard and eye hazard from exposure to either the direct or reflected beam; may also present a fire hazard."

xTool F1 Ultra or xTool F2 Ultra that works with the conveyor is a Class 4 laser machine. After the conveyor is installed on xTool F1 Ultra or xTool F2 Ultra, the protective enclosure of the laser machine cannot be completely closed. Diffused laser beams may leak out from the openings during operation, and you may be exposed to Class 4 laser radiation. When working with the conveyor, xTool F1 Ultra and xTool F2 Ultra are intended for professional use only, and more precautions are required for safe operation.

When using xTool F1 Ultra or xTool F2 Ultra with the conveyor, follow the safety precautions:

■ ONLY professionally trained personnel are allowed to use the product. A qualified Laser Safety Officer (LSO) must be designated and the product shall be operated by or under the guidance of the LSO. LSO is obliged to evaluate the laser safety risks and set up safety control mechanisms to ensure the safety of operators and prevent untrained persons from entering the laser radiation hazard area.

■ Before using the product, complete xTool's Laser Safety Awareness Training Course and review LSO Training documents, available at xTool Creative Space (XCS) and support.xtool.com/article/1171 for more information on Class 4 lasers, their uses, and their potential hazards. In the workplace context, you shall also receive adequate Class 4 laser product safe operation training as set forth in ANSI Z136.1, which is on the responsibility of the employer to provide.

■ Do not operate the product when any part of it is removed. Removing any part may expose the laser system and cause damage to the product.

■ When you use this product, wear safety goggles that can shield your eyes from 445 ± 15 nm and 1064 ± 5 nm laser beams and do not put your hands into the processing area. Avoid eye or skin exposure to direct or scattered laser radiation. Do not stare at the laser beam. You can visit support.xtool.com/article/1443 to find information about how to choose safety goggles.

■ When using xTool F1 Ultra or xTool F2 Ultra with the conveyor to process a material, pull down the protective enclosure until it remains no more than 5 mm above the material.

■ If your skin gets burned by laser beams, disinfect the skin with a povidone-iodine solution immediately and apply burn ointment to the wound. If you are severely burned, go to a hospital and see a doctor as soon as possible.

■ Do not use the product in public places, or on other occasions where untrained persons or children are present.

■ Ensure that only trained professionals with personal protective equipment enter the laser radiation area. You can visit support.xtool.com/article/1444 to learn about the Maximum Permissible Exposure (MPE) and Nominal Ocular Hazard Distance (NOHD) of Class 4 xTool laser machines.

■ You are advised to use xTool materials and recommended parameters for engraving. You can visit easyset.xtool.com and choose your device to find applicable xTool materials and the recommended parameter settings. If you are not using xTool materials or parameters recommended by xTool, or if you are not sure whether the material is applicable to your device, please contact our customer service at support@info.xtool.com for help to ensure safe operation and processing results.