Feature overview
With the Capture & trace feature on xTool C1, you can scan an image on a material and extract its outline for contour cutting. You can also add the extracted image to the canvas for further editing and design.

Scan

Trace
This article uses a printed sticker as an example to walk through the entire process, from scanning and tracing the image to adjusting the result and cutting along the traced outline.
💡The screenshots are for reference only. The actual software interface may vary.
Procedure
1. Connect the computer to the internet
Capture & trace requires an internet connection for image recognition. Make sure the computer is connected to the internet.
2. Connect xTool C1 to xTool software
Open xTool software and connect xTool C1. For detailed instructions, see: Connect xTool C1 to xTool Software.
3. Attach the material to the cutting mat and load it
💡Image requirements
• Make sure the image to be traced is clear and has distinct contrast with the background.
• If the image contains fine lines, colors similar to the background, or a complex background, manual adjustments may be needed after tracing.
Attach the material bearing the image flat to the processing area of the cutting mat (the area highlighted in green in the illustration). Make sure the material has no lifted edges or wrinkles.

Processing area of the cutting mat
Load the cutting mat into xTool C1.
🔔 After you place the cutting mat at the feeding inlet, the device will automatically feed the mat once detected. Do not force the mat into the device, as this may damage the device.

4. Open Capture & trace
After the material is loaded, the device automatically scans it, captures a background image, and transfers the image to the software.
If the background image does not appear on the software canvas, click Background Scan to capture it.

On the right panel of the editing page, click Capture & trace.

Click Start tracing to trace the entire image, or manually select an area before tracing.

💡Selection area
• The selected area affects the tracing result. If it is too large, unwanted background may be included. If it is too small, parts of the subject's edges may be missed.
• If the result is unsatisfactory, adjust the selection area and start tracing again.
5. Adjust the traced result
After tracing, compare the result in the Original and Preview areas. Zoom in or out and drag the image to inspect the details. Once the overall result looks correct, make further adjustments as needed.

5.1 Select the trace content
Depending on the intended use, select Outline or Image, or select both.
Option | Result | Example | Use case |
|---|---|---|---|
Select Outline only | Extracts the subject's edges and generates a vector outline. |
| Cut the image out of the material along its outline. |
Select Image only | Extracts the main image and removes the background. |
| Add the image to the canvas for further editing or printing. |
Select both Outline and Image | Generates both results described above. |
| Meet both of the above needs. |
5.2 Outline settings
When Outline is selected, adjust Offset and Node simplification as needed.
- Offset: Adjusts the distance between the outline and the edge of the image. At an offset of 0, the outline aligns with the edge of the image. Increasing the offset moves the cutting line farther away from the image edge, leaving more material around the image. Decreasing the offset moves the cutting line closer to the image.

Offset set to 0

Increased offset
- Node simplification: Smooths the outline. Increasing the value reduces sharp corners and indentations, making the outline smoother.

Before node simplification

After node simplification
5.3 Adjust the selection
After automatic tracing, if the selection includes unwanted background or misses part of the subject, you can refine it further.
Zoom in on the Original image and pay particular attention to the subject's edges and narrow gaps. Use the following tools to adjust the selection in the Original area.
- Retain: Adds parts of the subject that were not detected to the selection.
- Remove: Removes incorrectly selected or unwanted areas from the selection.
- Brush: After selecting this tool, click the areas to retain or remove directly in the Original area. You can adjust the brush size. A larger brush covers a larger area with each adjustment.

Original selection

After using Retain

After using Remove
- Magic wand: After selecting this tool, click a color in the Original area to retain or remove areas of similar color. Adjust Fuzziness to control the range of similar colors included.
💡Tips for adjusting the selection
Start with larger areas, then zoom in to refine the details. For reliable cutting, there is no need to preserve every tiny contour variation.
5.4 Apply the results and start processing
After completing the adjustments, click Apply to add the traced results to the canvas.

The extracted outline appears on the canvas as a vector path, while the extracted image appears as a bitmap.
Check the objects on the canvas and set the processing type according to the intended use:
- To cut directly along the image on the original material: Select the extracted outline and set the process type to Cut.
- To recreate the image on a new material: Configure printing and cutting as needed.
The following example shows how to cut along the image outline on the original material.
Before cutting, check the following:
- The material position has not changed: Keep the material in its original position on the cutting mat so that the scanned image remains aligned with the material's actual position.
- The outline is correctly positioned: Make sure the extracted outline stays in the correct position relative to the scanned image. Avoid moving, resizing, or rotating it unnecessarily.
Select the outline, choose Cut under Process Type, and select Kiss Cut or Die Cut under Cut Mode, depending on the material and desired result.
This example uses Kiss Cut, which cuts through only the sticker layer, not the release liner. This keeps the sticker attached to the release liner after cutting. Once the settings are configured, click Make.

On the processing setup page, make sure the settings for the loading method, material, processing tool, and other options match the actual setup. When using the material or settings for the first time, run a small test first. Once everything is confirmed, click Start.

When the device is ready, press the button on the device to start processing.
After processing is complete, follow the software prompts to unload the material and remove the finished piece. If using a cutting mat, support it while unloading.
Common issues
1. Tracing fails
Check that the computer is connected to the internet and try again. If the scanned image is blurry, incomplete, or has other obvious issues, scan it again before tracing.
2. The desired subject is not extracted
First, make sure the scanned image is clear and contains the entire subject. Adjust the selection area and try tracing again. A larger or smaller selection is not always better; adjust it based on the result and try again as needed. If only a small part is missing, use Retain to add it.
3. The tracing result includes extra background or stray fragments
First, adjust the selection area and trace again. Use Remove to clean up small leftover areas. Before clicking Apply, inspect the entire Preview area to make sure stray specks are not converted into cutting paths.
4. Multiple elements are connected
Try reducing the offset and check whether the outlines separate. If unwanted connections remain, use Remove to clean them up, then check the preview again.
5. The outline is not smooth enough or details are missing
Zoom in on the preview and inspect small details. If the outline has too many irregularities, increase the node simplification value to make it smoother. If sharp corners, indentations, or other details that need to be retained have been simplified, reduce the node simplification value.



