Introduction to Advanced Parameters for xTool X1
Updated Nov 17,2026
Updated Nov 17,2026

Overview

This article explains split width, scan mode, feather passes, feather dither, and the Synchronized and Tiled modes for vector line processing. It also provides test procedures for vector fills and bitmaps. The galvo can scan only a limited area at a time; to process a larger design, it must work with the X and Y axes. Suitable parameters and motion modes help balance processing uniformity, seam visibility, and efficiency.

Parameter

Applies to

Purpose

Adjustment or selection

Split width

Fills, bitmaps

Sets the side length of each square section

Smaller sections can improve uniformity but require more sections and joins.

Scan mode

Vector fills

Selects parallel-line or microspiral paths

Bi-directional is more efficient; Random reduces directional texture and seams.

Feather passes

Bitmaps, vector fills

Changes pass count or the number of line layers

Disperses heat in bitmaps and Random scanning; adds layers and energy in Bi-directional scanning.

Feather dither

Bitmaps

Randomly offsets laser points to reduce seams

Higher levels can reduce seams but may add grain or reduce detail clarity.

Synchronized and Tiled modes

Vector lines

Coordinates the X and Y axes with the galvo

Synchronized: both move together. Tiled: XY positions first, then the galvo processes.

Split width and Feather Dither are under Advanced settings. Feather Passes and scan mode are in the main parameter panel. Sections 1–4 explain parameters for fills and bitmaps. Section 5 covers Tiled and Synchronized modes for vector lines, and Section 6 provides test procedures for vector fills and bitmaps.

1 Split Width

1.1 What Split Width Means

Split width is the side length, in millimeters, of the square area the galvo processes at one time. If a design is larger than this size, the software divides it into sections, which the device processes and joins in turn.

Figure 1 Split width and the area processed in one galvo field

1.2 Why Adjust Split Width

Focus can vary between the center and edges of a single galvo field. With field curvature, defocus may increase toward the edges, making the laser spot larger and lowering its energy density. This can produce deeper engraving at the center and shallower engraving at the edges. Reducing the split width limits each section mainly to the more uniform central area of the field.

Figure 2 Field curvature and energy distribution within one galvo field

The table below relates split width to the energy zones and effects shown in the illustration.

Split width (mm)

Energy zones used

Effect

38–48

Extends to zones 1–2 at the outer corners

Severe defocus and darkening

22–38

Extends to zones 3–5

Slight defocus and a gray transition

14–22

Extends to zones 6–8

Near-focus region with a bright cleaned surface

5–14

Uses only zones 9–10 at the focus center

Highest energy

1.3 Effects on Processing Results

Split width mainly affects processing uniformity. Its effects are particularly noticeable in metal fill engraving, bitmap engraving, and oxidation effects.

Line engraving

Ideally, line width and color should remain consistent. With field curvature, lines at the center may be thinner and darker, while those near the edges and corners may become wider, lighter, and blurred.

Figure 3 Ideal line engraving and the effects of field curvature

Figure 4 Line details at the center, middle, and edges

Fill engraving

When processing the maximum area of a single galvo field, the center may be slightly darker, the middle more uniform, and the edges and corners gray with visible line texture because of insufficient energy. The maximum split width is 30 mm for the 5W UV galvo laser source and 48 mm for the MOPA and fiber galvo laser sources.

Figure 5 Ideal and actual fill engraving within one galvo field

When a design spans multiple fields, defocus and lower energy at the edge of each section may produce alternating light and dark vertical bands.

Figure 6 Ideal uniform fill across joined fields

Figure 7 Vertical bands caused by lower energy at section edges

Bitmap engraving

Within a single galvo field, field curvature may blur the image edges. The example below uses a split width of 48 mm to compare the ideal result with edge blurring.

Figure 8 Bitmap engraving within one field: ideal result on the left and blurred edges on the right

When a bitmap spans multiple fields, lower energy at each section edge may also cause uneven tones and visible seams.

Figure 9 Effects of field curvature on seams in a bitmap spanning multiple fields

1.4 Choosing a Suitable Split Width

First check uniformity within one section, then determine the upper limit for the split width used in seam testing. Reducing the split width usually improves uniformity, but also increases the number of sections and joins.

First test power and speed or dot duration to obtain the desired depth and tone. Then check uniformity within a single section. Use the following method to estimate a suitable split width for either vector fills or bitmaps before testing seams between sections.

1. Add a filled square to the software canvas. Set its side length and split width to the same value so that the square is processed within one galvo field. For the 5W UV galvo laser source, start with a 30 × 30 mm square. For a MOPA or fiber galvo laser source, start with a 48 × 48 mm square.

Split width test file

2. After processing, compare the center, middle, and edges. The example below uses a 60W MOPA galvo laser source on aluminum. Set the split width to 48 mm and process a 48 × 48 mm square. Check for uneven depth or tone and visible bands.

Figure 10 Split width settings and a single-field aluminum sample processed with MOPA

3. If the edges show uneven tones or bands, reduce both the square size and the split width, then process the square again. Repeat until the result is uniform within one section. Use this split width as the upper limit for subsequent seam testing.

Figure 11 Single-section samples produced while reducing the square size

2 Scan Modes

Scan mode determines the path used for vector fills. Bi-directional scanning follows parallel lines in alternating directions and offers higher efficiency. Random scanning uses microspiral paths to reduce directional texture and visible seams, but usually takes longer.

2.1 Bi-directional Scanning

Scan lines run in parallel at the specified line spacing. Adjacent rows run in opposite directions, forming a serpentine path. At the end of each row, the laser moves directly to the next row without returning to the start, reducing non-processing travel and improving efficiency.

Figure 12 Serpentine path used by Bi-directional scanning

Bitmap engraving scans back and forth row by row. For vector fills in Bi-directional mode, parallel lines are arranged in layers. If the design exceeds one galvo field, it is divided into sections, with the cut positions offset between layers to reduce visible seams.

Bi-directional scanning may leave directional line texture, and seams between sections may be more visible in large solid fills. Slight misalignment may also occur at row ends when the scan direction reverses.

2.2 Random Scanning

Random scanning distributes separate microspirals evenly across the design instead of using parallel straight lines. The total engraved line length per unit area is the same as that of a parallel-line fill at the same density.

The default microspiral diameter is 0.6 mm, and the spiral pitch equals the line spacing. Adjusting fill density mainly changes how closely the spirals are distributed; their diameter remains unchanged. Each spiral starts at a random angle and follows a path from the outer turn toward the center. The order in which spirals are processed is also dispersed to reduce directional texture.


2.png

Figure 13 Microspiral structure and processing order in Random scanning


Adjacent spirals overlap by default to cover the gaps between circles. The additional energy in these overlaps is part of the algorithm design. Random scanning applies only to vector fills.

Random scanning is suitable for large solid fills and can reduce directional texture and visible seams. However, it involves more path segments and non-processing travel, so it usually takes longer than Bi-directional scanning.

Figure 14 Bi-directional and Random scanning at section boundaries

2.3 Choosing a Scan Mode

Comparison

Bi-directional

Random

Path

Parallel lines in alternating directions

Evenly distributed microspirals

Texture

Visible directional lines

Less directional texture

Section seams

May be more visible

Usually less visible

Efficiency

Higher

Lower

Applications

Routine fills; efficiency is the priority

Large solid fills; uniform appearance is the priority

The large-area vector fill tests in this article use Random scanning.

3 Feather Passes

Feather Passes is represented by N and works differently for different processing methods. For bitmaps and Random scanning, the original paths are distributed across N passes without changing the total energy. The revised processing order disperses heat. Bi-directional scanning instead adds N layers of parallel lines at different angles. With other parameters unchanged, the total energy is approximately N times that of one layer, usually producing a much darker result.

Processing method

What Feather Passes changes

Total energy

Main effect

Bitmap engraving

Assigns rows to N passes, separating adjacent rows in time

Unchanged

Improves cooling and reduces vertical seam stripes

Vector fill with Random scanning

Keeps spiral positions fixed and distributes spirals across N passes

Unchanged

Disperses heat and reduces local hotspots

Vector fill with Bi-directional scanning

Adds N parallel-line layers at different angles

Approximately N times one layer

Improves coverage and edge smoothness; darkens the result

3.1 Bitmap Engraving

Each pixel is processed only once, so the total energy remains unchanged. Adjacent rows are assigned to different passes to separate them in time and allow heat to dissipate. Neighboring sections share an overlapping feathering band. The cut point of each row varies randomly within the band, and different passes use different band widths to prevent seams from aligning into one vertical stripe.

Figure 15 Bitmap rows assigned to passes within an overlapping feathering band

3.2 Vector Fills with Random Scanning

The software first places all microspirals at the target density, then assigns them cyclically to N passes in processing order. The microspiral positions remain fixed. Only their processing order changes, dispersing heat without changing the total energy.

Figure 16 Fixed spiral positions with processing order distributed across passes

3.3 Vector Fills with Bi-directional Scanning

N is the number of parallel-line layers. Each layer uses the full specified line density, with an angle difference of 180°/N between adjacent layers. For example, three layers are processed at 120°, 60°, and 0°. For a design spanning multiple fields, cut positions are offset between layers. The layer with the shortest cut is processed last to cover the earlier seams. Because every layer uses the full density, the total energy of N layers is approximately N times that of one layer.

Figure 17 Full-density line layers overlaid at different angles in Bi-directional scanning

3.4 Effects of Different Pass Counts

For bitmaps and Random scanning, the final points or lines remain unchanged; only the processing order changes. A larger N reduces consecutive heating of adjacent areas. In a simplified model, heat buildup at N = 4 is approximately 41% of the N = 1 value for bitmaps and 44% for Random scanning, reducing the risk of yellowing, overburning, and line thickening.

In Bi-directional scanning, changing N also changes the engraved texture. At N = 1, there is only one layer of parallel lines, which may leave visible line texture or discontinuous fine strokes. At N ≥ 2, the layers form a crosshatch pattern, improving coverage and smoothing edges. However, the color also becomes noticeably darker as N increases.

Figure 18 Simulated heat buildup and engraved texture at different feather pass counts

Note: The heat buildup shown is a simplified simulation for comparing relative trends. It does not represent measured values for all materials.

3.5 Setting Feather Passes

Recommended processing presets usually include a feather pass count. For bitmap engraving and vector fills using Random scanning, consider increasing this value when processing materials prone to heat buildup, such as acrylic and metal. Too many passes can reduce efficiency, so use a small-area test to choose a suitable value. For other materials that are less sensitive to heat buildup, 1–2 passes are usually sufficient.

4 Feather Dither

Feather Dither controls how far laser points are randomly offset from their original positions. It reduces visible seams in large bitmaps processed in sections, creating smoother transitions.

Increasing the setting usually makes seams less visible but may add grain to large uniform areas. Lower settings produce a cleaner, finer image but may leave more visible seams.

4.1 Effects of the Five Levels

Level

Effects and applications

Off

No random offset. Suitable for small bitmaps.

Slight

Slight pixel offsets with little visible change.

Weak

Solid-color areas may show some noise or pixel displacement.

Standard

Reduces grid texture but increases grain.

Strong

For extra-large or full-area bitmaps and heat-sensitive applications prone to seams. Strong offsets may blur high-contrast detail.

4.2 Reference Images Using Numeric Levels

The reference images below use numeric levels from 0 to 10 to illustrate how dither strength changes. The correspondence between these values and the current five named levels has not been confirmed. For testing, use the levels displayed in the software.

In xTool software, the numbers in the following figures stand for different levels. For example, 0 in the figure stands for Off in xTool software, 3 for Weak, 5 for Slight, 7 for Standard, and 10 for Strong.

Figure 19 Simulated patterns at numeric Feather Dither levels from 0 to 10

Figure 20 Portrait and cat samples processed at different dither strengths

4.3 Reference Levels for Different Applications

Application

Reference level

Full-area bitmaps with large blank or solid-color areas

Strong

Large bitmaps with large blank or solid-color areas

Weak or Standard

Small bitmaps

Off or Slight

5 Tiled and Synchronized Modes

These modes apply only to vector line processing. For fills and bitmaps, “joining sections” describes the processing sequence; it does not mean that the modes described in this section can be selected.

The X and Y axes move the laser module across a larger area. The A/B galvo mirrors rotate to scan the laser spot rapidly within a local field. The two modes differ in how these motions work together.

Synchronized mode: The X and Y axes move while the A/B galvo mirrors scan, working together to process the design. Because the two motions must be coordinated in real time, the galvo may not be able to make full use of its high scanning speed.

Tiled mode: The X and Y axes first move to a specified position and stop. The galvo then processes that area. Once the area is complete, the X and Y axes move to the next position and repeat the sequence. This mode helps make use of the galvo’s high scanning speed, but accurate joins between areas depend on device positioning and calibration accuracy.

Figure 21 Synchronized and Tiled motion for the same vector line


6 Feather power and Feather speed

Applies only to emobossing with a galvo source only (20W diode galvo module, 5W UV galvo source, 30W fiber galvo source, or 60W MOPA galvo source).

These settings control the processing power and speed of the feathering pass in embossing.

Higher power and lower speed reduce seams more effectively but remove more detail. Lower power and higher speed preserve more detail but may leave visible seams.

In embossing, the processing task consists of two stages: main engraving followed by feathering. During main engraving, the device engraves the relief tile by tile using raster scanning. The final feathering pass uses discrete line segments across the entire processing area to reduce seams throughout the design.

Setting Feather power above 0 enables the feathering pass. However, this pass can leave the surface looking rough. On materials such as brass and stone coasters, cleaning can resolve this rough appearance. On materials such as wood and glass, it cannot be avoided, so we recommend keeping Feather power at 0.

Figure 22

7 U Split Width

Available only when using a galvo source (20W diode galvo module, 5W UV galvo source, 30W fiber galvo source, or 60W MOPA galvo source) with a rotary attachment.

U Split Width sets the width of each processing segment along the rotary accessory’s U-axis. Adjust this width to improve processing efficiency. If the width is too large, the distance from the focal plane varies more across the segment, making seams more visible. If the width is too small, processing efficiency decreases.

Figure 23

8 Testing and Adjusting Parameters

First obtain the desired depth and tone within one section. Next, check uniformity and estimate the split width. Finally, test seams between sections. Change only the parameter being compared in each test, keeping all other parameters constant.

For both vector fills and bitmaps, follow Section 1.4, Choosing a Suitable Split Width, to check uniformity and determine the upper limit for split width in subsequent seam testing.

Note: The parameters and results below illustrate the testing method. They are not universal recommendations for all materials.

8.1 Testing Vector Fills

Vector fill test file

Step 1 Choose Depth and Tone

Create a 10 × 10 mm filled square and generate a power-and-speed test matrix with 10 rows and 10 columns. Each cell is 10 × 10 mm. The full matrix also includes cell spacing, so check that its overall size fits the material and processing area.

Test parameter

Setting

Matrix horizontal axis: power

10%–100%

Matrix vertical axis: speed

100–1,000 mm/s; increase the upper limit if needed

Feather Passes

6

Line density

200

Scan mode

Random

Other parameters

Defaults

Process the matrix, select a cell with suitable depth and tone, and record its power and speed. This example uses 40% power and a speed of 1,000 mm/s.

1.png

Figure 24 Vector fill power-and-speed matrix settings and sample

Note: These images show the test matrix and sample used in the example.

Step 2 Compare Seams

Create a 60 × 10 mm filled rectangle and generate a split width test array. Start at the upper limit determined in Step 2 and gradually reduce the split width. This parameter is under Advanced settings.

Keep the power and speed selected in Step 1, with Feather Passes set to 6, line density to 200, and scan mode to Random. Leave other parameters at their defaults. After processing, compare uniformity, seams, and texture to choose a suitable split width.

Figure 25 Split width test array and sample

Note: With the 5W UV galvo laser source, split width must not exceed 30 mm.

Compare the uniformity, seams, and texture of the samples, choose a suitable split width, and record the power, speed, and other fixed parameters. You can then adjust other parameters one at a time to improve texture, processing results, or efficiency. Some texture remains visible in the sample below; further adjustment may be needed for the desired result.

Figure 26 Vector fill engraving result

8.2 Testing Bitmaps

This example uses a 20W diode galvo module to engrave leather. First determine the result for the darkest areas, then estimate split width, and finally compare how dither strength affects seams and clarity.

Bitmap test file

Step 1 Set the Result for the Darkest Areas

Prepare a 10 × 10 mm solid-black bitmap and generate a test matrix with 10 rows and 10 columns to compare the darkest parts of the image. Before processing, check that the full matrix fits the material and processing area.

Test parameter

Setting

Matrix horizontal axis: power

10%–100%

Matrix vertical axis: dot duration

150–600 μs

DPI

Diode in this example: 254
Other sources for reference: UV 450; MOPA and fiber 350

Feather Passes

4

Feather Dither

Off (no dither)

Other parameters

Defaults

3.png

Figure 27 Bitmap power-and-dot-duration test matrix and sample

After processing, select a cell with a suitable result for the darkest areas. Record its power and dot duration.

Note: The images show the bitmap test matrix and processed sample.

Step 2 Compare Dither Strength and Clarity

Dither strength affects bitmap seams and may also reduce fine-detail clarity. Use a 60 mm-long grayscale gradient test image to compare seams, grain, and tonal transitions at each level.

Figure 26 Grayscale gradient for comparing seams and tonal transitions

Make five copies of the test image and set Feather Dither to Off, Slight, Weak, Standard, and Strong respectively. Keep the power and dot duration selected in Step 1, set split width to 22 mm, and keep DPI unchanged and Feather Passes at 4. Leave other parameters at their defaults. Feather Dither is under Advanced settings.

Figure 28 Test layout and samples at the five dither levels

Compare the samples and select a level that provides less visible seams and acceptable detail clarity. Record this level and the other processing parameters used in the test for future reference.

Figure 29 Bitmap processing result

Starting from these settings, adjust other parameters one at a time to compare results and efficiency. When changing the material, laser source, or desired effect, run another small-area test.

Preview
Was this page helpful?
15 out of 15 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.