Cleaning and Replacement Guide for Optical Components on xTool X1
Updated Oct 29,2026
Updated Oct 29,2026

After the 20W diode galvo module and galvo source are installed on xTool X1, the device has 9 optical components that may need to be cleaned or replaced as needed. This guide describes how to clean and replace these optical components.

Precautions

  • Before cleaning or replacing any optical component, disconnect the device from power and wait until it cools down to room temperature.
  • Clean or replace optical components in a dust-free or relatively clean environment.
  • Before operation, wash your hands thoroughly or wear dust-free gloves.
  • During operation, avoid touching the surface of any optical component with your fingers or hard tools.

Cleaning Tools and Methods

Choose one of the following methods.

Method 1: xTool Cleaning Kit (recommended, sold separately)

  1. Clean the area around the optical component to ensure the operating environment is relatively clean.
  2. Take out a lens wipe. Do not unfold it yet. Use the edge of the wipe to gently remove large dust particles and dirt from the surface.
  3. Unfold the wipe and gently wipe the glass surface in one direction until it is clean.

Note: The lens wipe is for single use only; do not continue to use it if it has dried out. For heavy dirt, it is recommended to use multiple wipes and clean the surface in separate passes.

  1. If there is still liquid residue on the surface:
  • Small optical components: Use a cotton swab to wipe in one direction until no water marks remain.
  • Large optical components: Use a cleaning cloth to wipe in one direction until no water marks remain.

Method 2: cotton swab / lint-free cloth + alcohol (not provided)

  1. Clean the area around the optical component to ensure the operating environment is relatively clean.
  2. Dip a cotton swab or dust-free cloth in alcohol, then gently wipe the glass surface in one direction until it is clean.

Tip: It is recommended to use cotton swabs for small optical components and lint-free cloths for large optical components.

  1. If liquid residue remains on the surface, use a dry cotton swab or dust-free cloth to wipe in one direction until no water marks remain.

Clean or Replace the CO₂ Optical Component Set

Tips:

  1. To replace components in the CO₂ optical component set, purchase the xTool X1 CO₂ Optical Component Set separately.
    image (1).png
  2. After cleaning or replacing the optical components, recalibrate the CO₂ optical path in xTool software.


Steering Mirror 1 (CO₂)

(1) Remove the 7 screws securing the top panel on the main unit.

Remove the seven screws securing the top panel

(2) Remove the panel.

Remove the top panel

(3) Take out the steering mirror.

Take out steering mirror 1

(4) Inspect the steering mirror.

Clean the reflective side of steering mirror 1

Note: Please clean the reflective side of the steering mirror.

  • If there are burn marks on the glass or it is heavily dirty and cannot be cleaned, replace the steering mirror.

Steering mirror 1 with burn marks or heavy dirt

(5) Install the cleaned or new steering mirror back into the device. Reinstall the cover and tighten the screws.

Steering Mirror 2 (CO₂)

(1) Take out the steering mirror.

Take out steering mirror 2

(2) Inspect the steering mirror.

Clean the reflective side of steering mirror 2

Note: Please clean the reflective side of the steering mirror.

  • If there are burn marks on the glass, or if it is heavily soiled and cannot be cleaned, replace the steering mirror.

Steering mirror 2 with burn marks or heavy dirt

(3) Install the cleaned or new steering mirror back into the device.

Install steering mirror 2 in the correct direction

Note: Ensure that the steering mirror is installed in the correct direction as shown in the image.

Steering Mirror 3 (CO₂)

(1) Remove the cover on top of the CO₂ module, then take out the steering mirror.

Remove steering mirror 3 from the CO₂ module

(2) Inspect the steering mirror.

Clean the reflective side of steering mirror 3

Note: Please clean the reflective side of the steering mirror.

  • If there are burn marks on the glass, or if it is heavily soiled and cannot be cleaned, replace the steering mirror.

Steering mirror 3 with burn marks or heavy dirt

(3) Install the cleaned or new steering mirror back into the device, then reinstall the cover.

Focusing Lens (CO₂)

(1) Detach the magnetic nozzle from the bottom of the CO₂ module.

Detach the magnetic nozzle from the CO₂ module

(2) Inspect the focusing lens.

Clean the CO₂ focusing lens

  • If there are burn marks on the glass, or if it is heavily soiled and cannot be cleaned, continue with the following steps to replace it.

CO₂ focusing lens with burn marks or heavy dirt

(3) Gently wipe the nozzle with a dry cloth to remove any dust that could contaminate the material being processed.

image.png

(4) Use the installation tool for optical window to loosen the retaining ring. Then remove the retaining ring, gasket, and focusing lens. Install a new focusing lens (with its convex side facing up), then reinstall the gasket and retaining ring.

Replace the focusing lens and reinstall the retaining ring

(5) After cleaning or replacing the focusing lens, reinstall the nozzle, which will magnetically snap back into its original position.

Reinstall the magnetic nozzle

Clean or Replace the Optical Component Set for the Galvo Source

Tips:

  1. To replace components in the galvo source optical component set, purchase the Optical Component Set for xTool X1 Galvo Source separately.

1d075314-04bc-41c9-baae-779bc7a7bcf6.png

  1. After cleaning or replacing the optical components, recalibrate the galvo source, camera, and flight galvanometer in xTool software.

Optical Window 1 (Galvo Source)

(1) Unplug the power cable and connection cable from the galvo source.

Unplug the cables from the galvo source

(2) Open the cover, remove the screws, and take off the galvo source.

Remove the screws securing the galvo source

Note: Hold the galvo source with your hand while removing the screws to prevent it from falling.

Take the galvo source off the main unit

(3) Inspect the optical window on the galvo source.

  • If the optical window is only slightly dirty, clean it with the cleaning tools. (For cleaning methods, see Cleaning Tools and Methods)

Inspect optical window 1 on the galvo source

  • If the optical window has burn marks, or if it is heavily soiled and cannot be wiped clean, continue with the following steps to replace it.

Optical window 1 with burn marks or heavy dirt

(4) Turn the old optical window counterclockwise to remove it, then install the new optical window.

Replace optical window 1 on the galvo source

(5) After cleaning or replacing the optical window, reinstall the galvo source on the main unit.

Optical Window 2 (Galvo Source)

(1) Inspect the optical window.

  • If the optical window is only slightly dirty, clean it with the cleaning tools. (For cleaning methods, see Cleaning Tools and Methods)

Inspect optical window 2 on the galvo source

  • If the optical window has burn marks, or if it is heavily soiled and cannot be wiped clean, continue with the following steps to replace it.

Optical window 2 with burn marks or heavy dirt

(2) Use the installation tool to loosen and remove the old optical window. Then screw in the new optical window by hand and tighten it with the installation tool.

Replace optical window 2 on the galvo source

Steering Mirror (Galvo Source)

(1) Take out the steering mirror.

Take out the steering mirror from the galvo source

(2) Inspect the steering mirror.

  • If the steering mirror is only slightly dirty, clean it with the cleaning tools. (For cleaning methods, see Cleaning Tools and Methods)

Clean the reflective side of the galvo steering mirror

Note: Please clean the reflective side of the steering mirror.

  • If the steering mirror has burn marks, or if it is heavily soiled and cannot be wiped clean, replace it.

Galvo steering mirror with burn marks or heavy dirt

(3) Install the cleaned or new steering mirror back into the device.

Install the galvo steering mirror in the correct direction

Note: Ensure that the steering mirror is installed in the correct direction as shown in the image.

Optical Window (20W)

(1) Inspect the optical window on the left side of the 20W diode galvo module.

  • If the optical window is only slightly dirty, clean it with the cleaning tools. (For cleaning methods, see Cleaning Tools and Methods)

Inspect the optical window on the 20W diode galvo module

  • If the optical window has burn marks, or if it is heavily soiled and cannot be wiped clean, continue with the following steps to replace it.

20W optical window with burn marks or heavy dirt

(2) Use the installation tool to loosen and remove the old optical window. Then screw in the new optical window by hand and tighten it with the installation tool.

Replace the optical window on the 20W diode galvo module

Clean or Replace the Lens Protector

Tip:

To replace the lens protector, purchase the xTool X1 Lens Protector separately.

2.png


(1) Remove the lens guard, then clean the lens protector with the cleaning tools. (For cleaning methods, see Cleaning Tools and Methods)

Remove the lens guard and clean the lens protector

If the laser power remains weak after cleaning the lens protector, continue with the following steps to check and replace the lens protector.

(2) Unscrew the cover in the direction indicated by the arrow, then remove the cover with the lens protector.

Unscrew the cover and remove the lens protector

(3) Check the lens protector. If the glass is burned or heavily dirty and cannot be cleaned, replace the lens protector according to step (4).

Lens protector with burn marks or heavy dirt

(4) Replace the lens protector, then install the cover and lens protector back to the device.

Note: Do not touch the glass with your fingers or other tools during replacement as the glass may get dirty. If the glass gets dirty or dusty, use a cotton swab to clean it.

Replace the lens protector and reinstall the cover

Preview
Was this page helpful?
4 out of 4 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.