xTool P2 User Guide
Updated Jan 6,2024
Updated Jan 6,2024

List of items

Open the box and take out all the items

  1. Open the lid and take all the items out.

 Note: If your machine contains the thumb screws and brackets that are used to fix the x-axis guide rails, remove them, move the x-axis guide rails forward, and take out the foam.

  1. Unscrew the screw that fixes the baseplate.

  1. Take out the foam and acrylic sheets and put the baseplate back into the machine.

  1. Tighten the screw that fixes the baseplate.

 

Meet your xTool P2


 

Understand the indicator and state display screen

Annular indicator

State display screen

Device

Blinking in white

/

Starting

Solid white

Displays the temperature and lid locked/unlocked state

Standby, not connected

Solid white

Displays the icon of the connection mode

Standby, connected

Breathing green

/

Sleeping

Blinking blue and then solid blue

/

Ready to work

Solid blue

Progress bar blinks and moves

Performing a task

Solid blue

Progress bar stops moving

Task paused

Solid green

/

Task completed

Solid white

/

Task canceled

Solid purple

/

Firmware updating

Solid red

Fault indicator lit up

Exceptions occur

/

H or L lit up

Liquid temperature alarm

H: Temperature too high

L: Temperature too low

Breathing blue

/

Calibrating or image recognizing

Solid red

/

Calibration or recognition failed. You can open and then close the lid or use XCS to bring the device back to the standby state.

Solid yellow

/

Waiting for AP network setting.

You can hold down the button on xTool P2 for 5 seconds to start AP network setting. If no network is set within 2 minutes, the device goes back the standby state.

Name of the AP hotspot: XTOOL-P2-Last 6 digits of MAC address

Note: "/" indicates no state change.

State display screen

  1. Progress bar, where you can see the progress of a processing task
  2. Lid locked/unlocked

Do not open the lid forcibly when it is locked. You can press the button on the machine to unlock the lid before opening it.

  1. The machine is connected through Wi-Fi.
  2. The machine is connected through the USB cable.
  3. Exceptions occur.
  4. Liquid temperature. H lighting up indicates that the temperature is too high; and L lighting up indicates that the temperature is too low.
     

 

Preparations

1. Check the casing of the machine. If it is severely damaged, do not use the machine and contact xTool after-sales services.

2. Remove the sticker used to prevent the lid from locking and turn the emergency stop switch to reset it.

3. Manually move the laser module to check whether it can move properly. If it can't, do not use the machine and contact xTool after-sales services.

4. Check the laser tube. If it is cracked or damaged, do not use the machine and contact xTool after-sales services.

(1) Unscrew the screws that fix the rear cover and remove it.

(2) Check whether the laser tube is cracked or damaged.

5. Fill the water tank with antifreeze.

You need to prepare a measuring glass to measure purified water.

If you can't find a measuring glass at home, you can store the antifreeze in another container and use the bottle of the antifreeze to measure purified water.

Note:

■ Do not pour the antifreeze directly into the water tank. Determine the volume of antifreeze to be used according to the annual lowest temperature in your region first.

■ Ensure that you use purified water to prepare the antifreeze. Tap water contains impurities and bleach, which may cause too many bubbles, affecting the working of the laser tube and even damaging the laser tube.

■ You need to fill the water tank twice. Strictly follow the steps to fill the water tank, using the recommended volume of antifreeze and avoiding overflow.

(1) Determine the volumes of antifreeze and purified water to be used.

Annual lowest

temperature in

your region (℃)

Concentration (%)

First filling

 

Second filling

Antifreeze (ml)

Purified water (ml)

Purified water (ml)

T > 0

0

0

1100

300

–10 ≤ T ≤ 0

20

280

820

300

–20 ≤ T ≤ –10

35

490

610

300

–30 ≤ T ≤ –20

45

630

470

300

–40 ≤ T ≤ –30

50

700

400

300

–50 ≤ T ≤ –40

60

840

260

300

(2) Open the cap of the water tank and insert the funnel into the opening.

(3) Complete the first filling.

Pour the required volume of antifreeze into the water tank, and then slowly pour the required purified water in. Observe the water level during the filling to avoid overflow.

(4) Connect the machine to a power supply and turn on the machine.

(5) Complete the second filling.

Wait 30s for the water level to descend in the water tank, pour the required purified water in, and then close the cap of the water tank. Observe the water level during the filling to avoid overflow.

(6) Fit the rear cover back to the machine and tighten the screws.

6. Install the smoke exhaust pipe.

If you have purchased a smoke purifier, follow the instructions to connect it to xTool P2.

 

Use xTool P2

You can use the xTool official software xTool Creative Space (XCS) to operate xTool P2. For details, see "Use XCS to operate xTool P2".

 

Was this page helpful?
46 out of 50 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Copyright © 2024 xTool All Rights Reserved.
Call Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales Hotline
+1(970)638-7030
Customer Service Hotline
+1(775)587-7760
Email Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales and shipping related
vicky@info.xtool.com
vicky@xtool.com
After-sales and shipping related
support@info.xtool.com
support@xtool.com
Technical Support
support@info.xtool.com(US)
support@xtool.com(US)
support.eu@xtool.com(EU)
support.uk@xtool.com(UK)
Brand Cooperation
If you want to cooperate with
xTool on causes like education,
public welfare, innovation, etc.,
or if you want to review our
machines, please email
partner@xtool.com
US headquarter
XTL US INC. 16035 Arrow Hwy.
Irwindale. CA91706
Copyright © 2024 xTool All Rights Reserved.