xTool D1 Pro Quick Start Guide
Updated Oct 20,2023
Updated Oct 20,2023

PDF files download

xTool D1 Pro Quick Start Guide-Part 1.pdf

xTool D1 Pro Quick Start Guide-Part 2.pdf

xTool D1 Pro Quick Start Guide-Part 3.pdf

 

Unbox and check

1.png

Plate components

A: Rear plate

B: Front plate

C: Left plate

D: Right Plate

E: Middle plate

 

2.png                     Shaft

 

17.png18.png19.png20.png
Laser moduleSafety gogglesMaterial packQuick Start Guide/ Instructions/Brochure

 

3.png4.png5.png6.png7.png
Power adapter & cableUSB cableMotor cableCable tie packLimit switch connection cable

 

8.png9.png10.png11.png12.png
TF cardCouplingScrewdriverHex key
13.png14.png15.png16.png
Parts storage boxScrew M4*8Screw M4*16Screw M4*25Nozzle connector components

 

21.png  
Aluminum sheet A4  

 

Assemble xTool D1 Pro

 

1. Fit the plates together

24.png

  1. Cut off the cable tie on the right plate. Note that no scissors are included in the pack.25.png

 

  1. Fit the four side plates together. Align the power switch, power port, and USB port with the openings on the right plate.

26.png

 

mceclip0.png

 

  1. Use screws to hold the side plates together.

mceclip1.png

mceclip2.png

mceclip3.png

 

  1. Use screws to fit the timing pulleys.

32.png

 

33.pngThe screws are used to set the tension of the timing belts. Do not fully tighten them. Otherwise, the timing belts may be damaged.

 

2. Fit the shaft

  1. Put the shaft through the coupling, and then put it through the timing belt and insert it into the idler pulley.

34.png

 

35.png28.pngIf you can't put the shaft through the timing belt, the possible cause is that the timing belt is set too tight. You can adjust its tension by turning the screw.

 

  1. Slide the coupling to the joint of the shaft and motor shaft.

36.png

 

Note: Keep a small distance between the coupling and motor, or the coupling can't rotate properly. 

mceclip1.png

 

  1. Slide the two sliders down against the front plate.

37.png

 

  1. Fully tighten the two screws on the coupling.

38.png

 

3. Connect the motor on the left plate to the main control board

  1. Insert the connectors into the port on the main control board and the one on the motor, respectively.

39.png

 

40.png28.pngPay attention to the front and back sides of the connector. Insert it properly.

 

  1. Use cable ties to fix the motor cable on the front plate.

41.png

 

4. Fit the middle plate

  1. Cut off the white cable ties on the middle plate and reserve the black ones.

42.png

 

  1. Insert the connector of the motor cable into the port on the motor.

43.png

 

  1. Align the middle plate with the screw holes on the sliders, and use screws to hold the middle plate and sliders together.

44.png

 

  1. Use the screw to fit the timing pulley.

45.png

 

33.pngThe screw is used to set the tension of the timing belt. Do not fully tighten it. Otherwise, the timing belt may be damaged.

 

5. Complete the wiring

 

  1. Connect the limit switch component on the middle plate to the one on the slider of the left plate.
  2. Insert the connectors of the laser module, motor, and limit switch connection cables into the ports on the main control board, respectively.

46.png

 

  1. Use cable ties to fix the connection cables on the right plate.

47.png

 

6. Install the laser module

  1. Install the nozzle connector and insert the plug.

48.png

 

  1. Connect the main control board and laser module.

49.png

 

  1. Fit the laser module on the middle plate.

50.png

 

  1. Use the thumb screw to fit the laser module.

51.png

 

52.png53.png54.png
Turn the handle clockwiseHold the handle to draw it away from the thread partRotate the handle to stop it from being blocked

 

55.png56.png
Release the handleTurn the handle clockwise again

 

33.pngYou may need to repeat this process multiple times to tighten the thumb screw.

 

28.pngUse the thumb screw

 

57.png

 

If the handle is blocked, you can tighten or loosen the screw as follows.

58.png59.png
Hold the handle to draw it away from the threaded part.

Rotate the handle to stop it from being blocked

The screw is not tightened or loosened.

60.png61.png

Release the handle

The handle goes back to the default position.

Rotate the handle to tighten or loosen the screw

 

7. Install the TF card

62.png

Great! The assembly is done.

 

Precaution

Prevent the middle plate and laser module from falling down themselves. Otherwise, the limit pieces may be damaged.

mceclip4.png

 

Meet your xTool D1 Pro

 

63.png

 

Set up xTool D1 Pro

Adjust the tension of the timing belts

64.png

 

33.pngTry to set the timing belts on the right and left plates to the same tension, so that xTool D1 Pro can cut and engrave materials properly.

 

Set the position of the laser module

65.png

 

66.png67.png68.png
Put the focal length setting bar downLoosen the thumb screw on the other side and slide the laser module upward or downwardAfter determining the position, tighten the thumb screw and put the focal length setting bar back

 

Set the position of the rear plate on the laser module

(Applicable only to the laser module of 20W)

28.pngTo cut thicker materials, you can adjust the position of the rear plate on the laser module, based on the scale with which the focal length setting bar is aligned, to ensure better cutting performance.

 

mceclip0.png

It's recommended that you adjust the position of the rear plate according to the thickness of the material to be processed.

 

mceclip0.png

After adjusting the position of the rear plate, you can still use the focal length setting bar to set the position of the laser module.

 

Download and install software

You can operate xTool D1 Pro by using our official software xTool Creative Space (XCS) or the third-party software LightBurn.

Note: You need to purchase LightBurn before using it.

 

71.png

For details about how to use XCS to operate xTool D1 Pro, see "Operate xTool D1 Pro with XCS."

For details about how to use LightBurn to operate xTool D1 Pro, see "Operate xTool D1 Pro with LightBurn."

 

Create with example projects

72.png

For details about how to create with example projects, see “Example Project - Making a Phone Holder.”

Before creating your works, you can place the aluminum sheet in the working area of xTool D1 Pro to protect your desk or floor from being smoked or burned.

 

74.png

 

28.pngIf the aluminum sheet is not flat due to film removing, you can use masking tape to stick it on your desk or floor.

 

Clean the laser module

When the light shield is dirty or laser beams can't cut a material, you need to clean the laser module.

 

  1. Turn off the device and remove the laser module from the device.
86.png

 

  1. Remove the nozzle and its connector from the laser module.

 

87.png

 

  1. Clean the inner and outer frames of the light shield with tissues or dust-free cloth moistened with alcohol, and clean the laser lens and infrared laser-emitting point with a cotton swab moistened with alcohol.

 

88.png

 

Was this page helpful?
56 out of 61 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Copyright © 2024 xTool All Rights Reserved.
Call Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales Hotline
+1(970)638-7030
Customer Service Hotline
+1(775)587-7760
Email Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales and shipping related
vicky@info.xtool.com
vicky@xtool.com
After-sales and shipping related
support@info.xtool.com
support@xtool.com
Technical Support
support@info.xtool.com(US)
support@xtool.com(US)
support.eu@xtool.com(EU)
support.uk@xtool.com(UK)
Brand Cooperation
If you want to cooperate with
xTool on causes like education,
public welfare, innovation, etc.,
or if you want to review our
machines, please email
partner@xtool.com
US headquarter
XTL US INC. 16035 Arrow Hwy.
Irwindale. CA91706
Copyright © 2024 xTool All Rights Reserved.