How to Install the Rotary Attachment for Laserbox Rotary
Updated Dec 21,2023
Updated Dec 21,2023

Part 1:List of items

The pack of the Rotary Roller Engraving Module comes with the following items:

 

Part 2:Meet the Rotary Roller Engraving Module

This additional attachment is placed inside of the Laserbox Rotary to support the cylindrical objects to be engraved. It consists of the following parts:

 

Part 3:Installing the Engraving Module in the Laserbox Rotary

  1. Before you begin,make sure the device is turned off, open the device's lid. Remove the two screws in front of the honeycomb plate and remove the tray.

  1. Remove the screws on both sides of the honeycomb plate and take out the honeycomb plate.

  1. Remove the six screws on the back of the tray and remove the plate.

  1. Put the tray back into the Laserbox.

  1. Put the Rotary Roller Engraving Module on the position shown in screen.

Attention:

Aligning the engraving module in the right position guarantees that the vertical axis of the cylinder is parallel to the vertical axis of the engraving.

 

  1. Plug the cable of the Engraving Module into the aviation connector of the Laserbox and tighten the nut. Keep the connection cable as close to the bottom as possible to prevent laser damage to the cable.

Attention:

The pack contains 2 connection cables. For the Laserbox Rotary, please use the connection cable shown in the figure below. The remaining cable serves to connect the Engraving Module to a different device.

 
  1. Turn on the Laserbox, open Laserbox software, and connect the device.

  1. The software detects the Rotary Roller Engraving Module and enters into cylinder engraving mode.

 

  1. Measure the diameter of the cylinder to be engraved and change the movable roller to the corresponding position. To know how to change the position of the movable roller, please read

'Part 4: Adjusting the position of the movable roller of the Engraving Module' of this user guide.

 

Attention:

70mms is the maximum diameter that a cylinder can have to be engraved.

 

  1. When the object's diameter is less than 30mm, The Rotary Roller Engraving Module needs to be raised to reach the focus range of the laser.

For example, if the diameter of the cylinder is 17mm, a flat object with a thickness of at least 13mm needs to be placed below the Rotary Roller Engraving Module.

Padding minimum thickness = 30-17mm = 13mm

If you can not find an object with a thickness of exactly 13mm, an object with a thickness greater than 13mm can be used as the padding object. If the object's thickness is 16mm, 16mm will be filled in the z-axis offset. 

 

Attention

If the surface of the engraved cylinder is smooth, such as glass, you can put a strip of masking tape (easy-to-tear, grainy stickers) around the top and bottom of the cylinder to prevent it from slipping and misaligning while rotating.

 

  1.  After entering the engraving mode, the software will automatically show a yellow line at the axis position of the cylinder, which indicates the starting position where the engraving will begin. If the position of the yellow line is not on the axis of the object to be engraved, drag the yellow line to the axis of the object.
  1. Import the pattern you want to engrave.
  2. Adjust the size of the pattern, as well as the cutting power and speed.

  1. Drag and drop the pattern you want to engrave onto the desired location.
  2. Click on the Send button.
  1. Press the start button on the Laserbox.
  2. Once the engraving operation is finalized, open the lid and take out the object.

 

Part 4: Adjusting the position of the movable roller of the Engraving Module

1) Measure the diameter of the cylindrical item to be engraved, and determine the position according to the following table:

PositionDiameter (units: MMS)
13-50
245-60
360-70

2) Set the engraving position. For example, you can take the following steps to change the engraving position from 2 to 1:

 

Part 5:Switching from the cylindrical to the 2D work mode

If you need to return to the 2D laser cutting/engraving mode, follow the next steps:

  1. Turn off the Laserbox
  2. Open the lid and unplug the cable from the Laserbox end of the Rotary Roller Engraving Module cable.
  3. Take out the Rotary Roller Engraving Module
  4. Put back the honeycomb board and drawer and close the lid
  5. Open the device and reconnect the software

 

Attention:

This process may result in Laserbox errors if the machine is not shut down, as indicated in step 1

Try not to unplug the connection cable at the Rotary Roller Engraving Module; this may lead to poor contact or even damage.

If the interface is not returned to the 2D laser cutting/engraving mode, press Ctrl+shift+k on the keyboard simultaneously, automatically switching to 2D laser cutting/engraving mode.

 

Part 6:Suggestions on power and speed parameters for certain materials

Material engraving parameters table
Material namePower(%)Speed(%)
Glass10020
Acrylic5080
Wood5080
Ceramic10020
Can10030
Stone5020

Attention:

For reference only, specific materials may vary. Users need to make adjustments according to the actual situation.

Preview
Was this page helpful?
1 out of 1 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Copyright © 2024 xTool All Rights Reserved.
Call Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales Hotline
+1(970)638-7030
Customer Service Hotline
+1(775)587-7760
Email Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales and shipping related
vicky@info.xtool.com
vicky@xtool.com
After-sales and shipping related
support@info.xtool.com
support@xtool.com
Technical Support
support@info.xtool.com(US)
support@xtool.com(US)
support.eu@xtool.com(EU)
support.uk@xtool.com(UK)
Brand Cooperation
If you want to cooperate with
xTool on causes like education,
public welfare, innovation, etc.,
or if you want to review our
machines, please email
partner@xtool.com
US headquarter
XTL US INC. 16035 Arrow Hwy.
Irwindale. CA91706
Copyright © 2024 xTool All Rights Reserved.