Introduction
CMYK inkjet printing opens up full-color creativity on far more materials than an ordinary printer can handle — but it has a learning curve. In our community, we keep seeing the same printing failures: designs bleeding along the wood grain, colors smearing on sticker sheets, and more.
This guide breaks down the logic behind those failures: why every material prints differently, and how the right pre-treatment and post-treatment get you the best possible results.
3 Things to Know Before CMYK Inkjet Printing
- There is no white ink. CMYK inkjet printing lays down no white base layer. White and light-colored materials reproduce colors best; black or dark materials are not suitable for color printing.
- Smooth surfaces do not absorb ink. Untreated acrylic, glass, and similar surfaces dry slowly, smudge easily, and hold ink poorly — always apply a primer first.
- Finished pieces need protection. For work that will be handled, gifted, or sold, apply a protective sealer after printing.
30-Second Material Quick Reference
Recommended = the material prints without a primer, but results are better with one.
Required = without a primer, the ink will not adhere reliably.
Material | Primer |
|---|---|
Paper / cardstock | Not required |
Inkjet sticker paper / temporary tattoo paper | |
Felt | |
Canvas bags / fabric | Recommended |
Plywood / wood board / MDF | |
Acrylic | Required |
Metal | |
Stone / rock | |
Glass | |
Ceramic |
Note: Because CMYK inkjet printing has no white ink, choose white or light-colored materials wherever possible for the truest colors.
xTool Official Primers and Sealers for Inkjet Printing
Product | When to use | What it does | Best for |
|---|---|---|---|
Before printing | Prepares wood for better ink adhesion and richer colors. Apply evenly and let dry; a second coat enhances results. | Wood boards and other wood surfaces | |
Improves ink adhesion on smooth, non-absorbent materials. Pair with Clear Matte Sealer for longer-lasting prints. | Acrylic, metal, glass, ceramic — surfaces that cannot be printed on directly | ||
Enhances color vibrancy and prevents ink bleeding on wood. Dries in 5 minutes; two coats deliver the best results. | Wood boards and plywood | ||
After printing | Protects metal from rust and moisture, plywood from warping and cracking, and gives glossy acrylic a matte finish. Apply thin coats 3 minutes apart and cure for 10 minutes. | Acrylic, metal, glass, plywood, and more |
CMYK Inkjet Printing on the 4 Most Popular Materials: How to Get It Right
1. Wood, Plywood & MDF
The most popular material for color printing — and the one where most printing problems happen.
Primer vs. No Primer: The Difference

— Alan Zenreich: "I am very pleased with the results. The difference between printing on raw wood and the surface treated with xTool Selected Wood Spray was impressive."
The difference is obvious. On the untreated board (left), the ink bleeds and the edges blur. Pre-treated with the print primer (right), the same design prints crisp and clean.
Tips:
- After using a spray or primer wipe, let the surface dry completely before printing. Light woods such as birch and basswood give the brightest colors.
- Colored MDF may be painted, stained, or otherwise finished — always test-print on a scrap corner before the final piece.
2. Acrylic
Inkjet printing on acrylic needs primer: the surface is smooth and non-absorbent. The final result also depends on the color of the sheet, and for the most vivid colors, white or clear acrylic is the best choice. Here is how different acrylic colors compare:
All samples below were pre-treated with the transparent print primer:
Acrylic type | Printing Results | Color print quality | Verdict |
|---|---|---|---|
White acrylic |
| Crispest print, most vivid colors | Best choice for color printing |
Light-colored acrylic |
| Good, but the base color shows through | Test first; suits high-contrast designs |
Clear acrylic |
| Good results | Great for creative displays |
Black acrylic |
| Colors barely show | Better for cutting and engraving than color printing |
3. Paper & Stickers
Paper and sticker products vary widely in coating and adhesive — and most are not designed for water-based inkjet inks. Paper that absorbs too quickly makes colors bleed and feather; paper that barely absorbs leads to pooling and smudging.
Choose official materials first: xTool papers and sticker sheets are fully tested with the matching machines and inks, so they print and cut cleanly in one pass. With third-party media, you are the test pilot.
If you do use third-party media, remember: only choose products explicitly labeled for inkjet use.
4. Fabric, T-Shirts & Canvas
Because the ink is water-based and not waterproof, washing will fade printed fabric.
So for wearables that need frequent washing, we do not recommend inkjet printing.
Pick the right materials for your machine in one go and skip the guesswork. Explore xTool's official materials collection, or find materials specifically selected for your xTool M2.
Have questions about working with materials, want to show off your creations, or want to be the first to know about new official materials? Join the Laser Materials & Craft Supplies Community on Facebook and connect with makers worldwide!




