Apparel Printer Film Roll
Updated Oct 8,2026
Updated Oct 8,2026

Product Overview

Apparel Printer Film is designed for high-quality DTF printing. It provides reliable ink absorption, vivid color reproduction, and consistent release after transfer. It is suitable for personalized apparel, fabric bags, footwear, handmade gifts, and a wide range of textile projects.

Recommended Heat Press Settings for Common Fabrics (First Press)

Fabric

Temperature

Time

Pressure

Cotton

100% Cotton

150-160℃ (302-320℉)

5-10 seconds

Medium (90 KG)

Polyester

100% Polyester

150-160℃ (302-320℉)

5-10 seconds

Medium (90 KG)

Cotton-Polyester Blend

65% Cotton

35% Polyester

150-160℃ (302-320℉)

5-10 seconds

Medium (90 KG)

Tri-Blend

55% Cotton

31.3% Polyester

13.7% Lyocell

150-160℃ (302-320℉)

5-10 seconds

Medium (90 KG)

Modal

39% Polyester

27.5% Cotton

27.5% Modal

6% Spandex

150-160℃ (302-320℉)

5-10 seconds

Medium (90 KG)

  1. Note: Actual results may vary depending on the compatibility between the fabric and the film. If edge lifting or missing areas occur, adjust the settings as needed. Perform a second press after peeling.

Step-by-Step Tutorial (Using a 100% Cotton T-Shirt as an Example)

Step

Key Points

1. Remove

Open the printer cover, lift the latch, and remove the installed film roll.

2. Install

Install the standard DTF film and lower the latch.
* Align the film with the white reference line.

3. Print

Edit the settings in xTool Studio, then start printing.

*Ensure appropriate ambient temperature and humidity before printing.

image.png

4. Cure

Set the OS1 curing temperature to 90–100°C. The machine will automatically apply the powder and cure the film.

5. Pre-Press

Pre-press the fabric for 2–3 seconds to remove wrinkles and moisture and help the design adhere properly.

6. First Press

Set the Wonder Press to 150–160°C (302–320°F), 5–10 seconds, and 90 kg. Refer to the recommended settings above for other fabrics. Align the design with the desired position, then start the heat press.
*For thicker fabrics, extend the pressing time or increase the pressure as needed.

7. Peel

Peel the film slowly and evenly.

8. Second Press(optional)

Cover the transferred design with a Teflon sheet or parchment paper and press it again.
*Use the same recommended settings as the first press. The pressing time may be reduced as appropriate.

Washing Instructions

  • Wait at least 24 hours after transfer before the first wash.
  • Wash below 40°C (104°F) using a gentle or delicate cycle.
  • Turn the garment inside out and avoid scrubbing the transferred design directly. Do not bleach or dry clean.
  • Tumble dry on low and remove the garment promptly after drying to prevent creases caused by prolonged compression. If air drying, avoid direct sunlight.
  • Iron inside out using low heat. Do not iron directly on the transferred design. If necessary, cover it with a Teflon sheet or parchment paper.

Precautions

  • Confirm the printing side before loading. Keep the film flat and align it with the white reference line.
  • Maintain moderate roll tension to prevent skewing, edge lifting, or feeding issues.
  • If the cured transfer will not be pressed immediately, keep it sealed in a cool, dry place away from high temperatures, humidity, and direct sunlight.
  • After opening, reseal the film and store it in a cool, dry place away from high temperatures, humidity, and direct sunlight.
  • Handle the roll carefully. When opening the package or cutting the film, control the force and angle of the cutting tool to avoid scratching the surface.
Preview
Was this page helpful?
12 out of 12 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.