Glow in the Dark Apparel Printer Film Roll
Updated Nov 6,2026
Updated Nov 6,2026

Product Overview

Glow-in-the-dark Apparel Printer Film is a special-effect transfer film developed for DTF printing. After absorbing natural or artificial light, the transferred design glows in dark environments. The glow is brightest at first and gradually fades over time. It is suitable for apparel, fabric bags, footwear, personalized gifts, and other textile projects.

Recommended Heat Press Settings for Common Fabrics (First Press)

Fabric

Temperature

Time

Pressure

Cotton

100% Cotton

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Polyester

100% Polyester

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Cotton-Polyester Blend

65% Cotton

35% Polyester

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Tri-Blend

55% Cotton

31.3% Polyester

13.7% Lyocell

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Modal

39% Polyester

27.5% Cotton

27.5% Modal

6% Spandex

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Note: Actual results may vary depending on the compatibility between the fabric and the film. If edge lifting or missing areas occur, adjust the settings as needed. Perform a second press after cold peeling.

Step-by-Step Tutorial (Using a 100% Cotton T-Shirt as an Example)

Step

Key Points

1. Remove

Open the printer cover, lift the latch, and remove the installed film roll.

2. Install

Install the glow-in-the-dark film and lower the latch.
* Coated side (rough side) facing upward.
* Align the film with the white reference line.

3. Print

Edit the settings in xTool Studio, set the white ink volume to 100%, and then start printing.

*Ensure appropriate ambient temperature and humidity before printing.

4. Cure

Set the OS1 curing temperature to 90–100°C. The machine will automatically apply the powder and cure the film.

5. Pre-Press

Pre-press the fabric for 2–3 seconds to remove wrinkles and moisture and help the design adhere properly.

6. First Press

Set the Wonder Press to 160–170°C, 20 seconds, and 100 kg. Refer to the recommended heat press settings above for other fabrics. Align the design with the desired position, then start the heat press.
*For thicker fabrics, extend the pressing time or increase the pressure as needed.

7. Peel

Allow the transferred design to cool completely, then peel the film slowly and evenly.

8. Second Press (Optional)

Cover the transferred design with a Teflon sheet or parchment paper and press it again.
*Use the same recommended settings as the first press. The pressing time may be reduced as appropriate.

Washing Instructions

  • Wait at least 24 hours after transfer before the first wash.
  • Wash below 40°C (104°F) using a gentle or delicate cycle.
  • Turn the garment inside out and avoid scrubbing the transferred design directly. Do not bleach or dry clean.
  • Tumble dry on low and remove the garment promptly to prevent creasing caused by prolonged compression. Alternatively, air dry away from direct sunlight.
  • Iron inside out using low heat. Do not iron directly on the transferred design. If necessary, cover it with a Teflon sheet or parchment paper.

Precautions

  • Print on the rough side with the glow-in-the-dark coating. Confirm the correct side before loading the film.
  • The transferred design must absorb sufficient natural or artificial light before it can glow. The intensity and duration of light exposure affect both the brightness and duration of the glow.
  • Light-colored designs generally produce a brighter glow than dark-colored designs.
  • Cold peel only: Allow the design to cool completely, then peel the film slowly and evenly. Do not pull or stretch the fabric.
  • For thicker fabrics, extend the pressing time or increase the pressure as needed to ensure proper adhesion.
  • For the second press, cover the design with a Teflon sheet or parchment paper. Use the same heat press settings as the first press.
  • If the cured transfer will not be pressed immediately or needs to be stored for an extended period, place it in a sealed bag and store it in a cool, dry place to minimize oil or moisture migration that may affect transfer quality.
Preview
Was this page helpful?
7 out of 7 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.