Gold/Silver Foil Apparel Printer Film Roll
Updated Sep 15,2026
Updated Sep 15,2026

Product Overview

Gold/silver Foil Apparel Printer Film is a metallic-effect transfer film developed for DTF printing. After heat transfer, the printed area takes on a gold or silver foil finish. Because the foil covers the printed color, use white ink for printing. It is suitable for text, logos, and decorative graphics that require a bold metallic appearance.

Recommended Heat Press Settings for Common Fabrics (First Press)

Fabric

Temperature

Time

Pressure

Cotton

100% Cotton

160–170°C (320–338°F)

20 seconds

Heavy (100 KG)

Polyester

100% Polyester

170°C (338°F)

20 seconds

Heavy (100 KG)

Cotton-Polyester Blend

65% Cotton

35% Polyester

170°C (338°F)

20 seconds

Heavy (100 KG)

Tri-Blend

55% Cotton

31.3% Polyester

13.7% Lyocell

170°C (338°F)

20 seconds

Heavy (100 KG)

Modal

39% Polyester

27.5% Cotton

27.5% Modal

6% Spandex

170°C (338°F)

20 seconds

Heavy (100 KG)

Note: Actual results may vary depending on the compatibility between the fabric and the film. If edge lifting or missing areas occur, adjust the settings as needed. Perform a second press after cold peeling.

Step-by-Step Tutorial (Using a 100% Cotton T-Shirt as an Example)

Step

Key Points

1. Remove

Open the printer cover, lift the latch, and remove the installed film roll.

2. Install

Install the gold foil film and close the film holder latch.

*Non-metallic matte side facing upward

*Align with the white marking line

3. Print

Edit the settings in xTool Studio, set the white ink volume to 100%, and then start printing.

*White ink is recommended for printing, as the gold or silver foil will cover the original printed color.

*Ensure appropriate ambient temperature and humidity before printing.

4. Cure

Set the OS1 curing temperature to 90–100°C. The machine will automatically apply the powder and cure the film.

5. Pre-Press

Pre-press the fabric for 2–3 seconds to remove wrinkles and moisture and help the design adhere properly.

6. First Press

Set the Wonder Press to 160–170°C, 20 seconds, and 100 kg. Refer to the recommended heat press settings above for other fabrics. Align the design with the desired position, then start the heat press.
*For thicker fabrics, extend the pressing time or increase the pressure as needed.

7. Peel

Allow the transferred design to cool completely, then peel the film slowly and evenly.
*Before peeling, gently flex and lightly rub the printed area to loosen the foil and help it release cleanly.

8. Second Press(optional)

Cover the transferred design with a Teflon sheet or parchment paper and press it again.
*Use the same recommended settings as the first press. The pressing time may be reduced as appropriate.
*After the second press, the transferred design will take on a slightly matte gold finish.

Washing Instructions

  • Wait at least 24 hours after transfer before the first wash.
  • Wash below 40°C (104°F) using a gentle or delicate cycle.
  • Turn the garment inside out and avoid scrubbing the transferred design directly. Do not bleach or dry clean.
  • Tumble dry on low and remove the garment promptly to prevent creasing caused by prolonged compression. Alternatively, air dry away from direct sunlight.
  • Iron inside out using low heat. Do not iron directly on the transferred design. If necessary, cover it with a Teflon sheet or parchment paper.

Precautions

  • Print on the non-metallic matte side. Confirm the correct side before loading the film.
  • This 75 μm film is thinner than standard DTF film. Align it carefully with the printer to prevent edge lifting and maintain consistent feeding.
  • Avoid extremely small text and very fine lines, as they may result in incomplete peeling or missing areas.
  • Complete the transfer within 30 minutes after curing to prevent moisture absorption.
  • Cold peel only: Allow the transferred design to cool completely before peeling the film. Peeling too early may prevent the adhesive from fully bonding to the fabric, resulting in edge lifting or incomplete transfer.
  • For thicker fabrics, extend the pressing time or increase the pressure as needed to ensure proper adhesion.
  • For the second press, cover the design with a Teflon sheet or parchment paper. The foil may appear slightly matte after repressing; this is normal.
  • After opening, reseal the film promptly and store it in a cool, dry place to prevent oxidation. Keep it away from sharp objects.
Preview
Was this page helpful?
8 out of 8 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.