Note: If the size or weight of the material to be processed is very small, you are advised to use tools such as tape to fix the material. Otherwise, the airflow of the exhaust fan may cause the material to change position during processing.

Note: By using the triangular prism working panel, you can reduce the areas burned during material processing and protect the baseplate. Ensure that the triangular prisms lie towards the smoke outlet.

There are two options available for the following steps.
To design a pattern and set parameters from scratch, please follow the procedure of "Option 1".
To use a previously saved project, please follow the procedure of "Option 2".

Note: If you can't find your material in the list, you can click + More to search among more materials in the xTool SELECTED online material center. If you still can't find the name of your material, you can select User-defined material.

Note: After you select a material on the material list or xTool Selected online material center, the software will automatically focus and set other parameters for laser processing. The default settings apply to xTool materials. You can adjust the settings based on your needs.

Note: To cut a material, you are advised to set the focus point at the middle of each cutting depth for the best cutting results.
For example, to cut a 6 mm thick basswood with one pass, it is recommended to set the focus point at 3 mm below the surface of the material. You can start by focusing on a 3 mm thick material. Then, do not change the focus setting, and replace the material with the 6 mm basswood to be cut.

Note: If you turn the knob clockwise, the laser module will move up, and the red light spot will move toward the left. If you turn the knob counterclockwise, the laser module will move down, and the red light spot will move toward the right.

Note: When the bottom of the laser module reaches the highest point, stop turning the knob up.

Note: If you are using Auto Focus for the first time after xTool F1 is turned on, you need to initialize xTool F1, so as to make its laser module back to the original position. Under Thickness, click Init, and then the laser module will move back to the original position.

Note: XCS supports importing the following image formats: SVG, DXF, JPG, JPEG, PNG, BMP, TIF, CR2, etc.

Note: If you select an image object, you can edit the image by using the tools on the right side of the canvas.

Note 1: You need to set parameters for every object. A missed object may fail to be processed. The parameters that can be set for bitmap objects and vector objects are different. You can select multiple objects of the same type and set parameters for them at once.

Note 2：xTool F1 integrates a blue laser with an infrared laser. You can select a Laser type for each object based on your needs.
Supported materials of blue laser: black alumina, metal name card, rock coaster, acrylic, aluminum sheet, wood, corrugated paper, cobblestone, etc.
Supported materials of infrared laser: black alumina, metal name card, rock coaster, acrylic, aluminum sheet, copper sheet, stainless steel, etc.

Note: xTool F1 supports two preview modes: Rect and Outline.
If you select Rect, you can preview the rectangular border of the processing area.
If you select Outline, you can preview the outline of the processing objects.

Note 1: During framing, keep the protective enclosure closed or wear goggles that can shield laser beams of 455 nm and 1064 nm wavelengths.

Note 2: To stop framing, click Stop framing in the software or press the framing button on xTool F1.

Note: Using the infrared laser for bitmap engraving at a low temperature may lead to unsatisfying engraving results. To ensure better engraving results, you can preheat the laser module before processing.

Note: During laser processing, keep the protective enclosure closed or wear goggles that can shield laser beams of 455 nm and 1064 nm wavelengths.

Note: A project file contains objects for processing and processing configurations for each object. You can adjust the objects and parameter settings before you start framing and processing.

Note: xTool F1 supports two preview modes: Rect and Outline.
If you select Rect, you can preview the rectangular border of the processing area.
If you select Outline, you can preview the outline of the processing objects.

Note 1: During framing, keep the protective enclosure closed or wear goggles that can shield laser beams of 455 nm and 1064 nm wavelengths.

Note 2: To stop framing, click Stop framing in the software or press the framing button on xTool F1.

Note: Using the infrared laser for bitmap engraving at a low temperature may lead to unsatisfying engraving results. To ensure better engraving results, you can preheat the laser module before processing.

Note: During laser processing, keep the protective enclosure closed or wear goggles that can shield laser beams of 455 nm and 1064 nm wavelengths.