Contents

List of items

Meet your Rotary Attachment

Connect Rotary Attachment to xTool M1

Use Rotary Attachment

Switch to Flat Surface Mode or Blade Cutting Mode

Appendix

Annular Indicator Description

User Guide of the Rotary Attachment 1 (RA1) for M1

Updated Jun 24,2024

List of items


Rotary Attachment	Connection cable	Hex key	User guide card

Meet your Rotary Attachment

You can connect xTool M1 to Rotary Attachment to engrave cylindrical materials.

Its components include:

1: Motor

2: Device connection port

3: Adjustable roller

4: Roller stand

5: Slot × 3

6: Fixed roller

Connect Rotary Attachment to xTool M1

Before operation, ensure that xTool M1 is powered off. Open the lid, remove screws that fix the baseplate and detach the baseplate from the machine.

Use risers to elevate xTool M1. Ensure that the risers are placed on a flat surface to keep the machine steady during operation.

Insert the white connector of the connection cable into the connection port of Rotary Attachment.

Place Rotary Attachment in the center of the working area with its motor facing the rear plate of xTool M1.

Insert the aviation connector into the connection port of xTool M1.

Use Rotary Attachment

Use the USB cable to connect xTool M1 to your PC.

Power on xTool M1 and connect it to xTool Creative Space.

Choose Cylindrical Processing mode.

Measure the diameter of the cylindrical material to be engraved and determine the gear as follows.

Gear	Diameter (unit: mm)
1	3-50
2	45-60
3	60-70

Steps to set the engraving gear:

(1) Remove the screw of the adjustable roller.

(2) Pull up the stand of the adjustable roller.

(3) Rotate the adjustable roller to the target gear.

(4) Put the stand of the adjustable roller into the target slot and press it into place.

Note: The side with a concave part faces away from the movable roller.

(5) Tighten the removed screw to the target screw hole.

5. Place four risers horizontally or vertically according to the diameter of the cylindrical material.

Diameter (unit: mm)	The way risers should be placed
3-20	Horizontally
20-70	Vertically

Note: The way the riser is placed determines how high xTool M1 can be elevated.

To keep the machine steady, ensure that all risers are placed in the same way and all machine feet are well put in the circular depressions of the risers.

6. Place the cylindrical material on Rotary Attachment, move Rotary Attachment to position the highest point of the material right on the red light spot, and then close the lid.

7. On xTool Creative Space, Click Camera, drag the yellow line to the highest point of the material and then click Auto-measure.

8. Import a project file or insert an element.

9. Adjust the image size, place the image closely on the right of the yellow line, and then set the parameters: material, speed, power, and pass.

10. Click Start and then click Send.

11. Press the button to start processing.

12. Take out the material after the operation is complete and the ventilator stops working.

Switch to Flat Surface Mode or Blade Cutting Mode

1. Turn off xTool M1. Disconnect it from the power supply before you remove the connection cables.

2. Remove the connection cable of Rotary Attachment, detach it from xTool M1 and then install the baseplate.

3. Close xTool Creative Space and open it again. Then its processing mode changes automatically.

Or click Switch to set the processing mode.

Appendix

Annular Indicator Description

	State	Description
Before operation	Normally on in white	Not connected
	Blinking in green	Network setting
	Normally on in blue	Connected
In operation	Blinking in blue	Performing a task
	Breathing in green	Task completed
	Breathing in white	Entering the sleep state
Other	Blinking in purple	Firmware updating
Other	Normally on in red	Exceptions occur

Preview

Was this page helpful?

26 out of 29 found this helpful

Help Ticket

Use this help ticket to submit your issue. We will respond within 1 business day

Submit a Ticket