Contents

List of items

Open the box and take out all the items

Meet your xTool P2

Understand the indicator and state display screen

State display screen

Preparations

Use xTool P2

xTool P2 User Guide

Updated Jan 6,2024

List of items

Open the box and take out all the items

Open the lid and take all the items out.

Note: If your machine contains the thumb screws and brackets that are used to fix the x-axis guide rails, remove them, move the x-axis guide rails forward, and take out the foam.

Unscrew the screw that fixes the baseplate.

Take out the foam and acrylic sheets and put the baseplate back into the machine.

Tighten the screw that fixes the baseplate.

Meet your xTool P2

Understand the indicator and state display screen

Annular indicator	State display screen	Device
Blinking in white	/	Starting
Solid white	Displays the temperature and lid locked/unlocked state	Standby, not connected
Solid white	Displays the icon of the connection mode	Standby, connected
Breathing green	/	Sleeping
Blinking blue and then solid blue	/	Ready to work
Solid blue	Progress bar blinks and moves	Performing a task
Solid blue	Progress bar stops moving	Task paused
Solid green	/	Task completed
Solid white	/	Task canceled
Solid purple	/	Firmware updating
Solid red	Fault indicator lit up	Exceptions occur
/	H or L lit up	Liquid temperature alarm H: Temperature too high L: Temperature too low
Breathing blue	/	Calibrating or image recognizing
Solid red	/	Calibration or recognition failed. You can open and then close the lid or use XCS to bring the device back to the standby state.
Solid yellow	/	Waiting for AP network setting. You can hold down the button on xTool P2 for 5 seconds to start AP network setting. If no network is set within 2 minutes, the device goes back the standby state. Name of the AP hotspot: XTOOL-P2-Last 6 digits of MAC address

Note: "/" indicates no state change.

State display screen

Preparations

1. Check the casing of the machine. If it is severely damaged, do not use the machine and contact xTool after-sales services.

2. Remove the sticker used to prevent the lid from locking and turn the emergency stop switch to reset it.

3. Manually move the laser module to check whether it can move properly. If it can't, do not use the machine and contact xTool after-sales services.

4. Check the laser tube. If it is cracked or damaged, do not use the machine and contact xTool after-sales services.

(1) Unscrew the screws that fix the rear cover and remove it.

(2) Check whether the laser tube is cracked or damaged.

5. Fill the water tank with antifreeze.

You need to prepare a measuring glass to measure purified water.

If you can't find a measuring glass at home, you can store the antifreeze in another container and use the bottle of the antifreeze to measure purified water.

Note:

■ Do not pour the antifreeze directly into the water tank. Determine the volume of antifreeze to be used according to the annual lowest temperature in your region first.

■ Ensure that you use purified water to prepare the antifreeze. Tap water contains impurities and bleach, which may cause too many bubbles, affecting the working of the laser tube and even damaging the laser tube.

■ You need to fill the water tank twice. Strictly follow the steps to fill the water tank, using the recommended volume of antifreeze and avoiding overflow.

(1) Determine the volumes of antifreeze and purified water to be used.

Annual lowest temperature in your region (℃)	Concentration (%)	First filling		Second filling
Annual lowest temperature in your region (℃)	Concentration (%)	Antifreeze (ml)	Purified water (ml)	Purified water (ml)
T > 0	0	0	1100	300
–10 ≤ T ≤ 0	20	280	820	300
–20 ≤ T ≤ –10	35	490	610	300
–30 ≤ T ≤ –20	45	630	470	300
–40 ≤ T ≤ –30	50	700	400	300
–50 ≤ T ≤ –40	60	840	260	300

(2) Open the cap of the water tank and insert the funnel into the opening.

(3) Complete the first filling.

Pour the required volume of antifreeze into the water tank, and then slowly pour the required purified water in. Observe the water level during the filling to avoid overflow.

(4) Connect the machine to a power supply and turn on the machine.

(5) Complete the second filling.

Wait 30s for the water level to descend in the water tank, pour the required purified water in, and then close the cap of the water tank. Observe the water level during the filling to avoid overflow.