Download PDF files (multi-language)
List of items
Unbox xTool Apparel Printer and check the items inside the pack. If you find items missing or broken, please get in touch with us for after-sales support.
 ① xTool Apparel Printer |  ② xTool Apparel Printer film holder and roll 25 m |
 ③ ④ Bracket |  ⑤ Output tray |
 ⑥ Ink 500 ml |  ⑦ Moisturizing liquid 500 ml |
 ⑧ Power cable |  ⑨ USB cable |
 ⑩ Syringe |  ⑪ Screwdriver |
 ⑫ Screw M4*16 (A spare screw is provided.) |  ⑬ Cleaner 100 ml |
 ⑭ Dropper |  ⑮ Cotton swab |
 ⑯ Tube |  ⑰ Cleaning cloth |
 ⑱ Print head protection box |  ⑲ Lubricating oil |
 ⑳ Plastic bag |  ㉑ Quick start guide |
 ㉒ Maintenance instructions |  ㉓ Safety instructions |
 ㉔ Essential guidelines | |
| Note: The power cable may vary according to kits. The illustration is for reference only. | |
Meet your xTool Apparel Printer
Product structure
Specifications
Product name | xTool Apparel Printer |
Size | 904 mm × 365 mm × 356.5 mm |
Weight | 34 kg |
Voltage | 110 V: 100 V – 120 V~, 60 Hz 220 V: 220 V – 240 V~, 50 Hz |
Rated power | 350 W |
Processing parameters | Maximum processing area (W × L): 356 mm × 460 mm Maximum processing speed: 1200 mm/s |
Print head model | Epson I1600-A1 |
Ink type | Water-based ink |
Ink tank capacity | Color ink tank: 500 ml White ink tank: 1000 ml |
Ink storage temperature | 5℃ – 35℃ |
Indicator description
Button indicator | Status indicator | Speaker | Device status |
Solid white | Solid white | / | Idle |
Going off | Going off | / | Standby |
Solid white | Solid green | / | Printing |
Solid white | Solid green | Sounding once | Printing paused |
Solid white | Blinking purple slowly | Sounding once | Firmware updated |
Solid white | Blinking purple slowly | Sounding once | Calibrate the print head |
Solid white | Blinking purple slowly | Sounding once | Clean the print head |
Solid white | Blinking red rapidly | Sounding once | Exception occurs |
Get xTool Apparel Printer ready
1. Prepare the print head
(1) Open the lid of the printer.
(2) Move the print head to the middle of the printer, and remove its cover.
(3) Move the print head to the right.
(4) Find the pinch roller switch in the printer. Toggle up the switch to open the pinch rollers.
2. Install the bracket and xTool Apparel Printer film roll
(1) Go through the four holes in the brackets with a screwdriver. Use four screws to secure the brackets on the printer.
(2) Make sure the brackets are secured firmly. Lift the locking bar on the left bracket.
(3) Install the roll on the bracket with the roll's two sides aligned with the notch of the bracket.
💡 Note: When placing the holder, mind your hands and make sure that the fasteners on both sides of the holder are secured properly.  |
(4) Press down the locking bar.
3. Feed film into the printer
| 💡 Note: Remove the sticker off the roll before feeding the film. |
(1) Feed the film into the printer through the feeding slot.
(2) Pull the film from under the pinch rollers.
(3) Adjust the guide plates on both sides to cover the film.
💡 Move the film until its side edges are in the center of the guide plate holes, as illustrated in the following figure. Note that the distance between the guide plate and the film should not be too close or too far. Otherwise, it may cause problems such as film bulging. |
(4) Press down the pinch roller switch and close the lid.
4. Fill in moisturizing liquid and ink
(1) Remove the ink tank cover, and open the cover of the moisturizing liquid tank.
Fill the moisturizing liquid into the moisturizing liquid tank. Close the cover.
💡 Note:
|
(2) Open the ink tank cover.
| 💡 Note: When filling ink, take care to prevent spills on your clothes. |
💡 When you use white ink, remember to shake it well before adding it.  |
(3) Open the cap of the ink bottle, remove the sealing film, and screw the cap back on.
Rotate the cap nozzle and remove it.
(5) Fill the ink into the ink tank.
| 💡 Note: After adding ink, be careful when you open the ink tanks again, as the ink may splash into the inside of the device. |
(6) Repeat the steps above to fill the other four ink colors. And close the ink tank covers.
(7) Put the cover back on the device.
5. Install the output tray
(1) Unfold the output tray.
| 💡 Note: When you use the shaker oven, it is necessary to open the two stands under the output tray. |
(2) Install the output tray into the slot.
6. Connect to a power supply and follow the setup
(1) Insert the connector end into the power port of the device and the plug end into the socket. The device powers on.
| 💡 Note: To ensure proper running and maintenance of the device, please keep it connected to a power supply. |
(2) Tap the screen to start the setup.
| 💡 Note: Complete the beginner's guide on the printer before connecting the printer to a computer and using the software. |
Use xTool Apparel Printer
1. Get the xTool software
Go to s.xtool.com/software to get the xTool software. Download and install the software.
2. Connect xTool Apparel Printer to your computer
Connect one end of the USB cable to the printer's USB port and connect the other end to your computer.
3. Use with the software
For details about processing materials using the xTool Apparel Printer and the software, visit Operate xTool Apparel Printer with the software.
Services & Help
Learn & Community
Contact Us
Copyright © 2025 xTool All Rights Reserved.