SafetyPro™ Air Purifier 2 (AP2) is your ultimate solution for purifying harmful dust and fumes produced during laser engraving. With its advanced filtration, it ensures that the air released meets quality standards for outdoor emissions.
💡Key features:
Dual Super Cyclone System: With this trailblazing technology, larger particles are efficiently separated, significantly enhancing the device's filter life.
Multi-Layer Filtration: The five-layer filtration system reduces volatile organic compounds (VOCs) to 0.1mg/m³ or 0.087ppm, while PM2.5 levels from basswood processing are kept below 8μg/m³. Additionally, the system ensures odor-free operation for a cleaner and more pleasant environment.
High-Pressure Fan: A high-powered fan, as potent as a cyclone, generates consistent airflow, even at a resistance of 1500Pa.
SafetyPro™ Air Purifier 2
“Cyclone” Tray
Which xTool laser devices are compatible with Air Purifier 2?
The Air Purifier 2 (AP2) is compatible with all current xTool models via two different pipe connectors:
Pipe connector 1: S1 & F1 Ultra
Pipe connector 2: M1 Ultra, M1, F1, P2 Series, D Series
Note: For P2 Series & D Series, the connection is secured by a pipe clamp included in the package.
Why are only some models compatible with Bluetooth linkage?
To link Air Purifier 2 (AP2) with a laser machine, a Bluetooth dongle must be plugged in.
Unfortunately, only S1, F1 Ultra, M1 Ultra, and P2S models are equipped with this Bluetooth dongle for seamless linkage.
Does the laser device's fan need to be disabled during the Air Purifier 2 (AP2) operation?
No. No need to turn off the laser device's fan.
Can the Air Purifier vent air outside after filtration?
Yes, the purifier comes with an exhaust pipe and connectors, allowing users to vent filtered air directly outside.
Can the purifier be connected to the laser device without the Bluetooth Dongle?
No, the purifier requires its Bluetooth Dongle to establish a Bluetooth connection.
What cleaner is recommended for maintenance?
Kitchen grease cleaner works best for dissolving fan surface grease.
What is the noise level of AP2?
Lowest: 55dB
Highest: 65dB
What are the storage requirements for the filters?
Store in a dry, ventilated environment at 5-60°C with 55% relative humidity.
Recommended storage time: 6 months for optimal filter performance.
What exhaust pipe specifications can the purifier's airflow inlet accommodate?
Pipe connector 1
Hard pipes: Compatible with inner diameters of 76mm and outer diameters of 85mm.
Soft pipes: Supports outer diameters between 65mm and 85mm.
Pipe connector 2
Hard pipes: Compatible with inner diameters of 51mm and outer diameters of 60mm.
Soft pipes: Supports outer diameters between 85mm and 110mm.
Is the AP2 compatible with third-party laser devices?
Yes, but only if your laser engraver's exhaust pipe and ventilation match the purifier's specifications, i.e. 150m³/h airflow, 60 - 110 mm pipe diameter.
Why does xTool Creative Space only display one purifier when two are connected via Bluetooth Dongle?
Unfortunately, xTool laser machines do not support connecting multiple devices of the same type simultaneously at the current stage.
Do I need to detach all other accessories before I update AP2's firmware?
Yes. For the AP2 firmware update to proceed smoothly, we recommend disconnecting all other accessories, such as the Fire Safety Pro and Air Assist Set. If the update fails, try re-pairing the AP2 with the laser engraver and then attempt the update again.
Still experiencing issues?
Should the issue persist after completing the preceding steps, submit a ticket via the "Submit a Ticket" button in the "Help Ticket" section below. The standard response time for xTool Customer Service is one business day.
For a prompt resolution, please include the following details:
Issue Description: A detailed explanation of the observed problem.
Video Evidence: Attach a video demonstrating the issue, where applicable.
Troubleshooting Performed: Any troubleshooting steps you have already attempted, along with their results.
This information is crucial for xTool technical support engineers to provide timely assistance.
Documentation feedback
Help improve this content by providing feedback. If this content did not meet your requirements, select "No" in the "Was this page helpful?" section below. Include specific details about what was unclear or missing in the pop-up suggestion box. Feedback submissions are reviewed by xTool technical writers to enhance future documentation.
Preview
Was this page helpful?
10 out of 18 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day