Unbox and check
Unbox xTool S1 and check the items inside the pack. If you find items missing or broken, please contact us for after-sales support.
| xTool S1 |
 | Laser module |
| Distance sensor |
| Smoke exhaust pipe |
| Key |
| Power cable and adapter |
| USB cable |
| Screw M3*8 |
| Screwdriver |
| Parts storage box |
| Material pack |
| User manual |
| Brochure |
Meet your xTool S1
Product structure
Indicator description
Buzzer | Logo indicator | Knob indicator | Machine state |
/ | Solid white | Standby | / |
Blinking purple | Network setting (device disconnected from the software) | Long press to set the network | |
Solid purple | Standby, connected to the software via Wi-Fi | / | |
Blinking white slowly | Starting | / | |
Auto focusing | Long press to cancel auto focus | ||
Measuring curved surface | Long press to cancel curved surface measurement | ||
Framing | / | ||
Solid blue | Locating the material | Short press to mark a vertex; long press to cancel material locating | |
Blinking green slowly | Performing a task | Short press to pause the processing; long press to cancel the processing | |
Blinking purple slowly | Firmware updating | / | |
| Blinking yellow for 3 times | TF card exceptions occur | / | |
Buzzing for once | Solid blue | Ready for framing | Short press to start framing; long press to cancel framing |
Ready to work | Short press to start the processing; long press to cancel the processing | ||
| Blinking blue slowly | Task paused | Short press to continue the processing; long press to cancel the processing | |
| Blinking red | Exceptions occur on movement | Short press to stop the warning | |
| Blinking yellow | The lid is not fully closed during operation. | / | |
Buzzing for 3 seconds | Blinking yellow | Exceptions occur | Short press to stop the warning |
| Blinking red | Exceptions occur on Wi-Fi communication | / | |
Keeping buzzing | Blinking red | Flame detected | Short press to stop the warning |
Specifications
| xTool S1 40 W | xTool S1 20 W | |
|---|---|---|
| Product certifications | IEC/EN60825 US: FCC FDA Canada: IC Australia and New Zealand: RCM, SAA United Kingdom: UKCA Japan: Telec, PSE European Union: CE-RED, ROHS, EN60825, CE-MD | IEC/EN60825 US: FCC FDA Canada: IC Australia and New Zealand: RCM, SAA United Kingdom: UKCA Japan: Telec, PSE European Union: CE-RED, ROHS, EN60825, CE-MD |
| Laser power | 40 W | 20 W |
| Spot size | 0.08 × 0.10 mm | 0.08 × 0.06 mm |
| Working speed | 600 mm/s | 600 mm/s |
| Working area | 498 × 319 mm (19.61 × 12.56 inches) | 498 × 330 mm (19.61 × 13 inches) |
| Working area with automatic conveyor feeder | 470 × 3000 mm (additional conveyor rails are required) | 470 × 3000 mm (additional conveyor rails are required) |
| Output voltage | 25 V 11 A | 24 V 8 A |
| Connection way | USB/Wi-Fi | USB/Wi-Fi |
| Supported system for XCS | Phone: Android & iOS Tablet: iPad Computer: Windows 10 or above & macOS | Phone: Android & iOS Tablet: iPad Computer: Windows 10 or above & macOS |
| Software | XCS/Lightburn | XCS/Lightburn |
| Supported file | SVG/DXF/JPG/JPEG/PNG/BMP/TIF | SVG/DXF/JPG/JPEG/PNG/BMP/TIF |
| Product weight | 20 KG | 20 KG |
| Product size | 765 × 561 × 183 mm (excluding riser base)
| 765 × 561 × 183 mm (excluding riser base)
|
Preparations before using xTool S1
1. Remove the rear limit pieces
Note: xTool S1 has limit pieces before both sides of the beam. The limit pieces are used to prevent slipping gears during shipping. Before using xTool S1, you need to remove the limit pieces first.
(1) Open the lid of xTool S1.
.png)
(2) Use the screwdriver to remove the rear limit pieces on both the left side and the right side.
.png)
.png)
.png)
.png)
.png)
.png)
Note: There are limit pieces on the front parts of the side panels. They are meant to prevent the beam from hitting the front panel. Be careful not to remove these limit pieces.
2. Install the laser module
(1) Open the lid and move the beam to a position convenient for operations.
.png)
(2) Connect the cable and the tube to the laser module.
.png)
(3) Align the locating pin on the back of the laser module to the hole on the linear guide block. Attach the laser module to the linear guide block. After inserting the locating pin, slightly lower the laser module to lock the locating pin into the slot.
.png)
(4) Adjust the laser module to make the two holes on the top panel align with the tapped holes on the linear guide block. Then, hold the top of the laser module in position and use screws to fix the laser module.
.png)
.png)
3. Install the distance sensor
Align the two protruding points on the back of the distance sensor to the holes on the right panel of the laser module. Then, guide the distance sensor toward the laser module until it attaches magnetically to the laser module.
4. Install the smoke exhaust pipe
(1) On the back of xTool S1, remove the four screws that secure the louver, and then remove the louver.
.png)
Note: Please do not leave the fan exposed. Otherwise, laser beams may leak out, and your hands may get hurt if you touch the fan during laser processing.
(2) Use four screws to fix the smoke exhaust pipe to the smoke outlet.
.png)
(3) Stretch the smoke exhaust pipe and put its end outside the window or connect its end to a smoke purifier.
.png)
5. Connect to power
Use the power cable and power adapter to connect xTool S1 with a power supply.
6. Insert the key
Insert the key to the corresponding port on the back of xTool S1.
7. Check the emergency stop button
Check the machine and ensure that the emergency stop button is not pressed.
8. Turn on xTool S1
Turn on xTool S1. Wait until the annular indicator turns on.
Use your xTool S1
Emergency stop
If errors or machine faults occur during material processing, you can press the emergency stop switch to power off the machine and stop the processing.
After you fix the processing errors or machine faults, you can turn the emergency stop switch to reset it, and the machine will restore its power.
Operation access control
You can use the keys to control access to the processing and related functions. Without a key, the machine cannot emit laser beams. By keeping the keys, you can prevent children or other people who do not have knowledge of laser operation from using the machine.
To prevent others from using your machine, you can remove the key to lock the processing and related functions.
To unlock the processing and related functions, properly insert the key.
For more information on how to operate xTool S1 through the xTool Creative Space (XCS) software, see:
Mon-Fri,9:00-18:30 PDT
Mon-Fri,9:00-18:30 PDT
vicky@xtool.com
support@xtool.com
support@xtool.com(US)
support.eu@xtool.com(EU)
support.uk@xtool.com(UK)
xTool on causes like education,
public welfare, innovation, etc.,
or if you want to review our
machines, please email
partner@xtool.com
Irwindale. CA91706