Use LightBurn to Operate xTool D1 Pro

Article author
support
  • Updated

Disclaimer

If you need to control xTool D1 Pro through LightBurn, download the official release of the LightBurn software. LightBurn is the third-party software, and therefore Makeblock Co., Ltd. shall bear no responsibility for any loss caused due to the operation of LightBurn.

The firmware of xTool D1 Pro has been tested in detail by Makeblock Co., Ltd, but incompatibility with the software or hardware may still occur. You can contact our after-sales service for technical support if errors occur due to incompatibility.

 

1. Download and install Lightburn

Go to https://lightburnsoftware.com/pages/trial-version-try-before-you-buy to download the latest version of LightBurn, and install it. If you are a new user, you have a 30-day free trial.

Note: Make sure you use the latest version of LightBurn.

Before you configure xTool D1 Pro, download the configuration file first:

xTool-D1ProV3.lbdev

1. Open LightBurn, click Devices on the Laser

Make sure that you start to configure xTool D1 Pro in this way instead of choosing Import Prefs from the menu. If you choose Import Prefs, the original configuration is overridden.

mceclip12.png

2. Click Import to import the file xTool-D1ProV3.lbdev.

mceclip13.png
mceclip14.png

3. The following device information is displayed after the file is successfully imported. (If the device still disconnects, please check the COM port.)

mceclip16.png

2. Operation guide--plane processing

1. Place a material to be engraved in the working area.

Put down the focal length setting bar to set the height of the laser head.

Note:

The center point of the cross-shaped light beams is the start point for framing. You can move the laser head to place the center point in the position where you want to start engraving.

5.png

2. Draw a square on the canvas.

mceclip17.png

3. Set the parameters.

mceclip18.png

4. Set the start origin.

mceclip19.png

5. Click Frame to see whether the pattern to be engraved is in the expected area on the material.

mceclip20.png

6. Click Start.

mceclip21.png

3. Operation guide--rotary processing

Install the rotary attachment on xTool D1 Pro

1. Fit cylindrical spacer blocks to the supports of xTool D1 Pro.

To use the rotary attachment, you need to fit cylindrical spacer blocks to the supports of xTool D1 Pro. Use the cylindrical spacer blocks supplied by Makeblock and fit them as follows:

(1) Remove the rubber ring from each support.

11.jpg

(2) Fit the rubber ring to each cylindrical spacer block.

12.jfif

(3) Fit the cylindrical spacer blocks to the supports of xTool D1 Pro.

13.jfif

Note:

If one cylindrical spacer block is too low to engrave an object, you can add one more spacer block.

2. Set the position of the adjustable roller on the rotary attachment and connect it to xTool D1 Pro.

Take the engraving on a stainless-steel cup as an example.

For details about how to set the position of the adjustable roller, see "Setting the position of the adjustable roller."

Connect the rotary attachment to xTool D1 Pro, as the following picture shows.

14.jpg

3. Place the rotary attachment in the middle of the working area of xTool D1 Pro.

15.jfif

Note:

Ensure that you have placed the rotary attachment parallel to the working area of xTool D1 Pro. Otherwise, the pattern to be engraved on the object may be deformed.

4. Focus the laser head.

(1) Set the laser head to the proper height by using the focal length setting bar, and move the laser head over the object to be engraved.

16.jfif

(2) Move the laser head again to position the center of the cross-shaped light beams at the start point to be engraved.

4. Use LightBurn

1. Click General Lightburn Settings on the toolbar.

mceclip22.png

2. Enable Show rotary enable on main window in the Settings, and click OK. Then the Enable Rotary button occurs.

2022-07-18_10-30-53.png

3. Choose Laser Tools > Rotary Setup.

mceclip23.png

4. Set the parameters for the rotary attachment as follows and click OK.

Steps:

  1. Choose your rotary type: Chuck or roller
  2. Enable rotary and "mirror output" (opt out if you are using roller rotary)
  3. Choose "Z Axis" for the rotary axis (for xTool D1 Pro)
  4. Enter the corresponding parameter for rotary
  5. Enter your object parameters.

11.png

5. Import the pattern you want to engrave and set the size of the pattern, the engraving power, and speed.

mceclip24.png

6. Enable Enable Rotary.

You can click Frame to preview the position where the pattern is to be engraved and then set the laser head to the expected position.

After completing the settings, click Start.

mceclip25.png

Note:

Currently, the firmware supports only some functions of the rotary attachment. Start From can be set only in Current Position.

 

For more information on xTool RA1 and xTool RA2, you can check the following document:

https://support.xtool.com/hc/en-us/articles/4408611185559-User-Manual-of-the-Rotary-Attachment-for-

D1-

https://support.xtool.com/hc/en-us/articles/4845194584215-User-Manual-of-the-Rotary-Attachment-for-

M1

https://support.xtool.com/hc/en-us/articles/4905858897559-User-Manual-for-Rotary-Attachment-2

 
 
 
 

Was this article helpful?

0 out of 0 found this helpful

Contact Us

Comments

0 comments

Please sign in to leave a comment.