The Processing Parameters for xTool F1 Ultra
Updated Jun 28,2024
Updated Jun 28,2024

Laser Type

xTool F1 Ultra supports two types of laser for processing: blue-light laser (20 W) and fiber infrared laser (20 W). You need to choose the proper laser type based on the material to be processed.
 
🔵 Blue light is typically used with materials like Tilia wood, corrugated paper, and leather, and for laser cutting.
🔴 Fiber IR (infrared) is ideal for engraving metals such as stainless steel, gold, silver, copper, aluminum, etc.
 

Power (%)

The power of the laser. The higher the power, the deeper the laser carves into the material surface. Valid value: [1, 100], integer.
 
 

Speed (mm/s)

The moving speed of the laser beam. If the laser beam moves slower, the processing time will be longer and the material will absorb more energy. Therefore, the smaller the speed, the deeper the laser carves into the material surface.
 

Pass

The number of times the laser passes over and engraves the material. The more passes, the deeper the laser carves into the material surface. Valid value for laser engraving: [1, 10], integer. Valid value for laser cutting: [1, 10,000], integer.
 
 

Lines per cm

The number of lines engraved within each centimeter.
 

Engraving mode

  • Bi-directional: The laser module emits light beams when it moves both from left to right and from right to left. Compared to the uni-directional mode, it takes less time to process a material. Due to backlashes, however, the processed patterns, especially the edges of the patterns, are not as clear as those processed in uni-directional mode.
  • Uni-directional: The laser module emits light beams only when it moves from left to right. Theoretically, it provides more detail as it does not require frequent changes in direction or complex corner paths. Compared to the bi-directional mode, it takes more time to process a material, but the processed patterns are clearer.
 

Dot duration

When processing bitmap, a complete image is formed by methodically doting each point. Hence the term "Dot Duration" refers to the time spent at each point, measured in microseconds (μs), and it affects the overall processing time. 
 
To ensure stable light output, especially for infrared lasers, we recommend setting more than 100μs. The optimal timing varies with the material but usually falls between 100 and 500. Please note that excessive dot duration could result in a whitening effect and a longer processing time.
 
 

DPI (Dots Per Inch)

DPI is a unit of measurement in dot matrix digital image, indicating the number of image pixels per inch. The setting range is [1, 1270]. When converted into linear density (lines per cm), 100 linear density equals 254 DPI.
 
A higher DPI theoretically yields a finer engraving image effect. However, when the DPI surpasses the bitmap's pixel distribution, overly dense dots can have a counterproductive effect, causing darker materials to appear whiter (shown in the image below ).

Bitmap mode

XCS provides multiple bitmap modes for selection, catering to most bitmap usage scenes. You can choose the type that best suits your image. Generally, we recommend Jarvis mode for infrared light and grayscale mode for blue light.
 

With the other settings unchanged, the output of an image on a wooden board varies according to image mode, as shown in the following figure.

 
  • Grayscale

Transforms an image into the grayscale mode. A grayscale image has pixels that are formed by the shade of gray between black and white, which may be the darkest one in black or the brightest one in white. The darker the grayscale pixel, the deeper the engraving.

  • Jarvis 

Jarvis is a dithering mode that provides a softer transition between pixels than Floyd mode and renders good results on almost all images.

  • Bayer

Looks like adding a special grid mosaic filter to an image.

  • Floyd

Dithers the image by using the Floyd algorithm that diffuses the error to neighboring pixels. And the dithering is extremely subtle, resulting in a fine, less distorted, and detailed image. It is recommended for highly-detailed images but not for images with monochrome.

  • Stucki 

Stucki is a dithering mode that processes slightly faster than Jarvis mode and produces a cleaner and sharper image.

  • Atkinson

Dithers is a similar algorithm to Jarvis and Sierra that preserves details well. But we do not recommend using it in a very dark or bright environment, where exposure may occur.  

  • Sierra 

Sierra dithers based on Jarvis mode and they process with similar results on images. But the sharpness of Sierra is higher. 

 

Frequency

Frequency indicates the number of times the infrared laser emits light per second. The greater the frequency, the faster the speed of light output, but the lower the peak power.
Was this page helpful?
47 out of 49 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Copyright © 2024 xTool All Rights Reserved.
Call Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales Hotline
+1(970)638-7030
Customer Service Hotline
+1(775)587-7760
Email Us
Service Time
Mon-Fri,9:00-18:30 PDT
Pre-sales and shipping related
vicky@info.xtool.com
vicky@xtool.com
After-sales and shipping related
support@info.xtool.com
support@xtool.com
Technical Support
support@info.xtool.com(US)
support@xtool.com(US)
support.eu@xtool.com(EU)
support.uk@xtool.com(UK)
Brand Cooperation
If you want to cooperate with
xTool on causes like education,
public welfare, innovation, etc.,
or if you want to review our
machines, please email
partner@xtool.com
US headquarter
XTL US INC. 16035 Arrow Hwy.
Irwindale. CA91706
Copyright © 2024 xTool All Rights Reserved.